wltoys 144001 front bumper 3d models

Easy to print front bumper to protect damper.

This bumper works great! I prefer to use 3m tape to stick it on the bottom plate. ...It just pops off in case of a realy hard crash and doesn´t rip out your differential mounting screws...

... in PLA and PETG. ...print on side seems best. require supports. I don't care it works and looks good any ways. The canard sometimes is difficult to extract supports. Attach what you like to it. Bumper extension. Wing. Bash bar. ...Winch......

Modified the original design to accomodate the upper 2 screw holes, making it more sturdy. ... 299 174 10.07

<p>Modified the original design to accomodate the upper 2 screw holes, making it more sturdy.</p> <p>299 174 10.07</p> Category: R/C Vehicles

Simple bumper. ...Very similar to stock

Created this front bumper since no other design had a good mounting system on the top while using the metal diff covers. Since this should be printed in TPU( but can also work with PLA) it needed 2 mounting points. Also modified the design to look...

Front bumper for WLToys 144001 including mounts for headlights, designed for Proline 1/16 Raptor body and using these mounts: https://www.thingiverse.com/thing:4626922. Headlights used were these:...

Front bumper for WLToys 144001 including mounts for headlights, designed for Xinlehong 1/16 body and using these mounts: https://www.thingiverse.com/thing:4626922. Headlights used were these:...

Front bumper for the Wltoys 144001. ...The design is inspired from the Kyosho Optima Mid bumper.

Bumper for the Wltoys 144001. Will ft both the front or rear. I went through a few iterations to get it to the right size and have the right amount of flex. Let me know what you think about it. ... The curve starts off shallow so I recommend using...

A massiv Front Bumper . ...but you need longer screws

I found a similar design but the width was far too small to protect the wheels and front arms then I also has the idea to include a 6mm diameter carbon tube. ... I hop you will like this design and a small tip is welcome to finance my printing...

Designed for my Wltoys 124019, but I assume will work for 144001, but I have not tried this as I do not have one. Required 2 M3x8 bolts and nuts to hold the top through the shock tower. ... I have extensively bashed mine and its survived many...

This are two Bumpers for the WLToys 144001 1:14 RC Car. ... Can be fit to the LC Racing 1:14 Car.

This are two Bumpers for the WLToys 144001 1:14 RC Car. ...Can be fit to the LC Racing 1:14 Car.

Compatible with the original wheels. ... This bumper works great and is indestructible! ...You have to use 2 longer screws below to put it in place correctly and then it won't move anymore.

The original Design is too flexible when printed in TPU. ...I added some Stabilizer and holes for the front screw. ...Also removed some material to save some weight.

WLtoys front arm. Just mirror it for the other side. ...The arms ar stonger and almost unbrakable with nylon carbon filament ;-)

... PETG for this one and it seems to hold quite well. This is a 3-part assembly so please check the drawing for more details. Components: 1 x Bumper_rev05 2 x Bumper_rev05_01 Post your make and let me know if we need to consider changes. ...Thanks.

After done the rear / tail light for 144001 it´s time for the front light! Space for 12 3mm leds (i used yellow leds). ... 3 parallel strips composed of 4 leds in series with a 22 Ohm resistor.

I bought the Kaboom Body from Phatbodies , I could use the rear body mount but I needed a new front mount for it , Just get screwed in plave with 4 screws on the front suspension plate , added 1 version with longer pin.

I bought the Kaboom Body from Phatbodies , I could use the rear body mount but I needed a new front mount for it , Just get screwed in plave with 4 screws on the front suspension plate , added 1 version with longer pin.

Wltoys 144001 front and rear shock tower 3mm. ... SVG files added for cnc.

Front bumper for wheel protection. Printed in PLA with dense infill (more infill will make it stronger). EDIT: Added a filled in version 2 for more strength. I broke 2 of the honeycomb model. ...Print Settings Printer: Anet A8 ...

Not able to get the remix option in thingiverse to work.*** ***I accidentally drove the car off a footstool today and the car nose dived straight into the hard floor taking a direct hit on the front wing and it suffered no damage at all so it may...

This cover is printed in 2 parts and protects the front shocks from damage in a rollover.

... (which also fits the WLToys 144001). ... I used this in combination with a custom front bumper (https://www.thingiverse.com/thing:4634082) to add front and rear protection with headlights and tail lights on my 144001 with the Proline 1/16 Raptor body.

A wider bumper for the [Wltoys 989](http://bit.ly/2CWze3f) which provides some extra protection to the front of the car. The original bumper is not very wide, but made of foam. A printed, stiffer, bumper might cause the bumper mounting to break more...

Wltoys Tower shock protection protect the front shocks and the tower from scratch