xt30 caps 3d models
77906 3d models found related to xt30 caps.thingiverse
- Simple XT30 connector cap with symbols, you don't need 3 colors of TPU :)
cults3d
Simple XT30 connector cap with symbols, you don't need 3 colors of TPU :)
thingiverse
XT30 cap. After trying some designs, no one were fitting good, too small. So we decided to create our XT cap designs. ...Post-Printing
thingiverse
XT30 battery caps or covers for LiPos. There are 2 cap STL files included, one with a "+" and "-" symbols to indicate the state of charge. These are a snug fit and best printed with TPU or TPE flexible filament. ... Scale +2-5% if printing with PLA.
thingiverse
I use XT30 batteries on smaller planes and such. ... I like having caps on my batteries to keep track of which ones have been charged and which ones have been used.
thingiverse
Protects the contacts on Lipo batteries at the same time denotes state of charge. ... Also included small storage cases.
thingiverse
two XT30 caps for male connectors. one a little loose and one snug i used TPU. ...but i think the lose one can be printed in PLA as well
thingiverse
I bought a LiPo battery with a XT30 connector and I bought some spare XT30 connectors. So I went looking on Thingiverse for a cap to protect the plug when not in use. I found this version here https://www.thingiverse.com/thing:2087961 and a remix...
cults3d
I bought a LiPo battery with a XT30 connector and I bought some spare XT30 connectors. So I went looking on Thingiverse for a cap to protect the plug when not in use. I found this version here https://www.thingiverse.com/thing:2087961 and a remix...
thingiverse
I made these battery caps to cover the conenctors of my 2S and 4S LiPo batteries. If printed in TPU they fit tight enough to not fall off but are not hard to remove. I added a small tab at the top to be able to grab them easier. ...They are modeled so...
thingiverse
I don't like carrying around 20 different caps to be able to indicate if my batteries are full or empty. ...With this cap, you can it in two colors and just flip it over to indicate the charge level.
thingiverse
This cap is desing to print with TPU only if you print with non flexible material it will not work , TPU is excellent for this application it gives you a nice rubberize fit. ... I also did a XT60 https://www.thingiverse.com/thing:2510964
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
This is an XT30 cap to prevent shortcuts when keeping LiPo batteries in a bag and to indicate charge. It's ribbed for easier removal, even with a tight fit. Also included is an STL as a regular cap instead of a doubled one. Pause the print at...
prusaprinters
This is an XT30 cap to prevent shorts when keeping LiPo batteries in a bag and to indicate charge. ...It's ribbed for easier removal, even with a tight fit.Also included is an STL as a regular cap instead of a doubled one.Pause the print at 7.5mm for...
thingiverse
Inside Thingiverse I could not find an XT30 cover that fit my connectors precisely, or they were too tight or too loose, so I decided to design an XT30 cover myself.
thingiverse
as the names suggest, one version says "XT30" on the flat side and the other does not. I use these to protect the connectors from damage in transport and to keep them from shorting on accident. I print in ABS for now so it works pretty well there;...
thingiverse
Remix of https://www.thingiverse.com/thing:4550886 Engraved on both sides. ... The original data was slightly loose, so it was reduced to 98%. I made a new XT30 version.
thingiverse
This is an XT30 / XT60 / XT90 Cap, it fits over the female side (battery side) of lipo batteries. It has a small lip on the bottom to make it easier to pull apart. Should fit snug. I use these to determine if the battery is charged or not. When I use...
thingiverse
Plug with color battery indicator for xt 30 and xt60 connector. You can print it both in PLA and TPU. In case of PLA I recommend to print it at 102%. ... PRINTER: ARTILLERY GENIUS SIZE OF BED: 220x220 MATERIAL: PLA or TPU Nozzle: 0.4...
thingiverse
Improved XT30 Charge Indicator Cap I had printed several other designs but, for reasons unknown, they were not a snug fit on the XT30 connectors. I started from scratch with a slightly under-sized cover, adding the 'waist' protrusions and making...