zyliss vise soft jaws 3d models

I just got a Zyliss vise and wanted soft jaws. There is another version of Zyliss soft jaws here on Thingiverse ( https://www.thingiverse.com/thing:3749322 ) but they were a bit too loose, so I designed my own which I printed in TPU. This is not a...

Only one side in the file, for the other duplicate and MIRROR. ... Soft Vise Jaws 4''

Soft Jaws for bench vise with 68cm or 3 inch jaws made with flex filament. ... I printed this at 245 degrees with a bed temp of 50 degrees

This is soft jaws for my 6" Wilton vise. This might fit other vises, however, I have not tried other vises... ... I used PLA, and ABS as the material for this and it printed fine.

The soft jaws are attached to the vise using strong 5mm neodymium magnets. Three versions of the soft jaws are included: 3in, 4in and 5in. ... Print Settings Printer Brand: RepRap Printer: MakerFarm i3V 10 Rafts: Doesn't Matter Supports: Doesn't Matter...

Soft jaws for a 5" vise. They simply slide on from the side. It was designed for our Irwin vise but i think it will also fit the harbor freight vise, have not confirmed this though. print standing up, tall ways. pla is plenty strong enough. ...

This model is base on my previous Vise Soft Jaw Design (http://www.thingiverse.com/thing:1376177). The length and width of the soft jaws can be altered to accommodate any vise. As well the knurling pattern on the front jaws face can also be...

So, I drew these soft jaws up. Work great. OpenSCAD source code included, so you can customize it to your vise. This was drawn up for a Harbor Freight Dyole 4-1/2" SKU 57737. Other Doyle vices probably only need the length changed. Other...

Flexible jaws for sheap ebay vise. ...Horisontal and vertical v-groove

Soft Jaws for bench vise with 68cm or 3 inch jaws made with flex filament. ...I printed this at 245 degrees with a bed temp of 50 degrees</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p class="detail-setting...

###Overview: This design is for a 5" wide set of magnetically fixed vise soft jaws. ###Revisions: Initial Release - September 6, 2020 ###Details: This 5 inch (127mm) wide soft jaws design includes several geometric features in order to clamp...

Printed soft jaws for small vice, 80mm wide. Inserted magnets 4x6x8mm. ...Included Fusion360 design.

Soft jaws with holes for magnets, which is to be held in by snap rings.

This is a jaw for a generic 8" vise with m6 mounting screws at 120mm spacing-- total dimensions are 200x22x13mm. ... There are two files -- one for a "flat" jaw and one for notched (for clamping on small curved objects)

Overview: This design is for a 5" wide set of magnetically fixed vise soft jaws. Revisions: Initial Release - September 6, 2020 Details: This 5 inch (127mm) wide soft jaws design includes several geometric features in order to clamp various objects...

[Bench...

vice jaws yup that's it! ...tpu 20% infill is good, two files one wth little holes one without.</p>

Designed to fit over existing jaws which are 3.75in x 1in and 5/16 in thick. They are held in place with magnets glued in with Loctite GO2 Glue (I've had hit or miss with other glues and like that the best). 0.03 in over sizing is added to each...

Reversible soft jaws for OML 15 wide vise.

Removable Jaws for vise.

Soft jaw covers for Irwin 10WR "The Original" vise grip pliers. ... Printed using NinjaTek Cheetah flexible filament.

soft jaws for a 100mm vise designed for my STANLEY 1-83-066 vise print recommendations: -PETG -100% infill -orientation as in added picture -support >60° (only inside)

First project with Fusion 360. ... Soft jaws for a very cheap C clamp vise with 36mm jaws. ... The holes are 1mm to 6mm in diameter

Soft jaws for a 6" vise. Holes on back are locations to epoxy in magnets. ... Parts were printed with 3 shell, 80% infill.

The soft jaws I had bought from various sources all did not fit on my vise, so I decided to design my own.

First project with Fusion 360.Soft jaws for a very cheap C clamp vise with 36mm jaws.The holes are 1mm to 6mm in diameter.

I've designed a new soft jaw for Irwin 5" vises. this one is modeled after the AN fitting soft jaws for assembling AN lines. great for gripping hex bolts and such. AN stands for Army Navy. These fittings are very popular in the automotive industry.

Soft jaws for a 6" vise. Holes on back are locations to epoxy in magnets. Parts were printed with 3 shell, 80% infill. ...Print Settings Printer Brand: MakerBot ...

This thing was made to enclose the particular steel faces of my vise, which has the dimensions of 12mm x 21mm x 151mm, and I've added a 1.4mm overhang to ensure the soft jaws don't pull off the vise during use. In my photos, I've added some inset...

Customizable soft jaws for a bench vise. The default values fit nicely on my 125mm grizzly bench vise. They stay in place without magnets. Once you've got the fit dialed in, it would probably be best to print with fairly heavy fill. Updated...