1 4 tripod screw 3d models
1282879 3d models found related to 1 4 tripod screw.thingiverse
Printed in PET-G at 0.4 nozzle, layer 0.3, walls 1.2. ...
thingiverse
Searched all over thingiverse (and others) for a file with the 1/4-20 screw, even if I had to pull just the screw STL out of another project to use, had no luck what-so-ever. So, I've created a set of 1/4-20 screws that will mount into the c920 for...
thingiverse
Vertical rotations are made by untighten the screws and tighten them at an specific angle. There are also markings every 30 degrees. Some parts are meant to be glued together after print for witch I would recommend superglue, witch should be used...
cults3d
Just a simple webcam mount for the i3 Mega by Anycubic. ...Its made to fit 1/4" tripod mount scres that a lot of webcams can accept. ... Prints great with 20% infill and no supports.
thingiverse
Just a simple webcam mount for the i3 Mega by Anycubic. ...Its made to fit 1/4" tripod mount scres that a lot of webcams can accept. ... Prints great with 20% infill and no supports.
thingiverse
Another modification, but for my flat monitor with using 1/4" tripod mount screw that perfectly fits for this (and because I do not know how to find another non-metrical american screws). On photo you can see that screw is little bit higher then...
thingiverse
No changes from original beyond opening up the mounting hole to allow a standard 1/4-20 tripod screw. This permits many more camera options. I ultimately did not use this mount in my LACK enclosure build, because my camera choice was too long to...
thingiverse
I made a Tripod Adapter which adds 2 1/4" tripod screws instead of 1 on a normal tripod. This is useful for many things, including Mixed Reality with the HTC Vive, where you'll want to be able to mount your camera and Vive Tracker to the same rig. I...
thingiverse
A shorter version of the tripod screw by Basic3Dprinting. This takes three turns off the other screw and is designed to turn with a penny instead of a hex bit. Works great and thank you to the original designer! ...How I Designed This Remixed / made...
thingiverse
IPhone 5s holder The holder attaches to a standard camera tripod 1/4-20 bolt and nut interface. The holder has holes to access home button and headphones minijack. Tip: The headphones volume button can be used as a remote camera trigger when plugged...
thingiverse
I found that you can use cheap harbor freight screws as tripod screws, so I just bolt my action cam right on it. I liked the concept of the [original](https://www.thingiverse.com/thing:4647485). The reason I was using this design is because I do...
prusaprinters
... LCD</a>. ... This mod allows for a standard US tripod to be used.Directions: Print with the tripod mount facing print bee. No supports are needed. ... Unscrew the stock mount and use same screws to attach the print.
thingiverse
This screw for Compact Camera Tripod - foldable by Kernel770 https://www.thingiverse.com/thing:1460181
grabcad
Camera mounting thread 1/4" Base mounting thread 1/4" This locking ball head makes adjusting your camera to nearly any position quick and easy. Simply loosen the knob, and rotate, tilt and pan your camera or camcorder with complete fluidity. ...And...
thingiverse
1/4-20 screw for use in a tripod mount socket. This one is 30 mm long. ...I have uploaded two variants, both are 30 mm long but differ on the diameter of the head.
thingiverse
Tripod head printed in regular mode Tripod legs printed in vase mode with 0.8 nozzle without bottom layers
thingiverse
Simple Tripod Adapter with 1/4 Screw 100% Infill for Screw Modeled in Fusion 360 (projects attached)
thingiverse
I combined parts of Sneaks designed thumb bolt and MasterFX's Camera tripod Screw (1/4"-20 UNC) https://www.thingiverse.com/thing:213425/files The Camera Tripod is bigger than the original Thumb bolt so I had to extend a MFLink. It's not perfect as...
thingiverse
tripods are sold with only one quickrelease.... so i designed one for my second (small) camera... al the parts are 3d printed.... this is version 2, version one had several issues. The only remark is that you have to put some non slippery surface...
thingiverse
Simple remix meant to accommodate a 1/4-20 x 0.5 inch screw. ...Threading may need additional tapping, Thread Measurements taken from online resources.
thingiverse
Tpu Flex GoPro HERO 4 case frame mount 1/4 screw tripod
thingiverse
A quick remix of the tripod screw and the knurling nut done with tinkercad to make a knurled tripod screw.
thingiverse
A simple camera tripod screw with printed thread. ...Stable enough for compact and DSLR Cameras with small Lenses.
grabcad
Screw for fixing e.g a tripod to the base of your camera e.g EOS 650D
thingiverse
This tripod screw is enforced with an 3mm (M3) countersink screw. It is stable enough to hold bigger DSLR firmly in place. It has no problems with my quite heavy Sony A850 full frame DSLR. It feels just like an all metal screw. Despite it is quite...
prusaprinters
Please note that there are two different files: “Camera screw 1_4 original UNC” features the original thread dimensions as defined for UNC ¼-20 while “Camera screw 1_4 3D printing” has a slight thread surface offset to compensate 3D printing effects...
thingiverse
During that sketching I've designed one with head also to attach my Netatmo Weather Station outside :) The files: * Tripod Screw 15mm - The one with no head * Tripod Screw Complete - This one has 8mm and the head is 5mm to make it easier to grab. *...
cults3d
During that sketching I've designed one with head also to attach my Netatmo Weather Station outside :) The files: Tripod Screw 15mm - The one with no head Tripod Screw Complete - This one has 8mm and the head is 5mm to make it easier to grab. You...
thingiverse
Needed a slightly longer version than the original pins: * (Original) `screw_1-4_15mm.stl` -- 22mm total length with 15mm threaded section * (Remixed) `screw_1-4_20mm.stl` -- 27mm total length with 15mm threaded section Another option is to use one...