1 fan 3d models
974259 3d models found related to 1 fan.
thingiverse
Customized version of https://www.thingiverse.com/thing:4681765 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4681765
thingiverse
12v DC 40x40x10 2-in-1 fan duct for stock Sunhokey extruder. ...I design this fan duct so it can move around the fins because I love to see the printing.
thingiverse
this is a 2 in 1 fan duct for mini with chimera hotend il post my combination that I use, work ok until 70 degrees overhang. ... https://www.thingiverse.com/thing:2844094 https://www.thingiverse.com/thing:1600018
thingiverse
Modding my Afox Rx550 into a 1 fan card setup, thickens the card from a 2 pcie slot design to 3 slot, but shortens the card length. Use with case fan's screw, the screw hole for your 9cm fan is a tad small, but still worked for me. ... I've only test...
thingiverse
2-in-1 fan duct for the printrite diy printer. This is the 3rd version wich i think is quite good and worth uploading here. Basically it directs some of the air flow from the fan in to the tip of the nozzle to cool the plastic coming out of it while...
prusaprinters
2-in-1 fan duct for the printrite diy printer. This is the 3rd version wich i think is quite good and worth uploading here. Basically it directs some of the air flow from the fan in to the tip of the nozzle to cool the plastic coming out of it while...
myminifactory
This is a fan mount, made for a 30mm Ruddog fan. ...fitting under the battery holder. If your battery is thicker than a IP 3200mah, you just ahve to shim the battery holder.
thingiverse
Customized version of http://www.thingiverse.com/thing:273099 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=273099
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
thingiverse
Support de ventilateur pour Associated B6.1 ou T6.1. ... A fixer sur la barre de la batterie. Fan bracket for Associated B6.1 or T6.1. ... To fix on the bar of the battery.
cults3d
Fan mount for the Team Associated B74.1. I have found that the original fan mount tends to rotate forward caused by hard landings crashes etc. ... This fan mount sits snug against the chassis support brace and cannot rotate, so your fan always sits...
cults3d
this is a hotend and print cooling fan setup. ...Uses 3x 30mm fans - 2 for cooling the print, 1 for cooling the hotend. ...Originally designed to clamp with a M3x50mm screw, it works better with a ziptie.
thingiverse
THIS IS A FAN ATTACHMENT FOR A PRINTRBOT +2.1. ...IT DIRECTS AIRFLOW TO IMPROVE COOLING OF EXTRUDED FILAMENT. Instructions PLACE OVER THE FAN AND EXTRUDER THEN USE A SHORT LENGTH OF 1.75MM FILAMENT TO SECURE THRU THE TOP LOOPS.
thingiverse
Uses 3x 30mm fans - 2 for cooling the print, 1 for cooling the hotend. Originally designed to clamp with a M3x50mm screw, it works better with a ziptie. ...Print Settings Printer: FrankenPrinter ...
thingiverse
This is a combination of designs from the users Thorped and ellioal. ... I wanted to make a one-piece fan duct with just 2 screws for my Wanhao v2.1 in order to reduce noise and weight. ... Hope it helps ;)
thingiverse
...In the past I worked with Noctua Fans and I can say that the NoiseBlocker fans are not as good but pretty ok for the price you pay. If you want the Board to be closer or farther away from the control board you can scale the spacers in the slicer.
thingiverse
This is a simple fan shroud probably made by hundreds of others but this one works for a Noctua 40mm Fan. It works with the existing mount for the original MP Select V2.1 Currently it works by the screws just screwing into the plastic holes, I am...