1 inch garden hose adapter 3d models
1036448 3d models found related to 1 inch garden hose adapter.thingiverse
1/2 0.5 inch (approx 13 mm) hose barb to male garden hose adapter
thingiverse
1 1/2 Inch Radiator Hose to Garden Hose Coolant Flush adapter. PLA is fine as it is running cool water. Works awesome. ...I also posted a 1 3/4 inch model.
thingiverse
1 3/4 Inch Radiator Hose to Garden Hose Coolant Flush adapter. PLA is fine as it is running cool water. Works awesome. ... I also posted a 1 1/2 inch model.
cults3d
Adapter for garden hose to .25" (7mm) ID vinyl irrigation tubing, used for dehumidifier. One side is a standard US female garden hose connector (1" / 25mm). The other side is a barbed vinyl hose connector, 7mm nominal inner diameter. Print with...
thingiverse
Adapter for garden hose to .25" (7mm) ID vinyl irrigation tubing, used for dehumidifier. One side is a standard US female garden hose connector (1" / 25mm). The other side is a barbed vinyl hose connector, 7mm nominal inner diameter. Print with...
thingiverse
3/4 inch garden hose (GH) male fitting x 1/4 inch national pipe thread (NPT) female fitting Versions are the same except 0.5 inch length on each side and 0.6 inch length on each side. 0.5 inch recommended. Prints well at 0.3 mm layer height. ...
thingiverse
There are various 1-1/4 inch (1.25") and 1.5 inch vacuum hose adapters that can be used to connect a variety of vacuum hoses and attachments. I printed these because I could not find them sold anywhere. I printed mine vertically at .2mm height,...
thingiverse
3/4-11.5 NH (Standard garden hose thread in the US and Canada) to 1/2" hose. This design can accept a standard garden hose washer to create a seal between the drain connection and this adaptor, but this may not be required in some cases. This was...
thingiverse
40mm NATO to 1 Inch hose adapter. ... Just a simple adapter from a thread to hose.
grabcad
40mm NATO to 1 Inch hose adapter.Just a simple adapter from a thread to hose.
thingiverse
Allows for the attachment of a 1.25 pool hose to garden hose print the o-ring using TPU
thingiverse
i modified the garden hose to screw it with a 1" filet
thingiverse
This is just a simple adapter to attach a garden hose to a .75 inch tube. Should also work to attach to a broken hose with hose clamp. Made using Makerbot Replicator 2: High Resolution, 10% infill and 2 Shells. Do not use supports. Supports will fill...
thingiverse
A 45 degree Y-adapter for 1-inch schedule 40 PVC to two 1/2 inch barbed hose connector. ...I designed this for the return line on my reef tank where space was limited.
thingiverse
A hose fitting for installation on a pipe with a 1/2-inch thread is presented. ...
thingiverse
This is an adapter from standard 1 inch pipe to 38mm hose for hot tube drain. ... I have added a design without barbs as eventually I had to file them off to have a practical fit on the plastic 38mm wire.
cults3d
This is an adapter from standard 1 inch pipe to 38mm hose for hot tube drain. ...I have added a design without barbs as eventually I had to file them off to have a practical fit on the plastic 38mm wire.
thingiverse
Fits the inside of a 1 1/4 inch PVC pipe to a US garden hose. Use some plumbers tape! v2 has a wider center diameter. I've found you don't need quite so much strength for it to work. I've also found that printing in TPU is very effective for...
thingiverse
simple half inch 4 way adapter, it was design without support , petg should be water tight, PLA could interduce some leaks over time, haven't test that long, paint acrylic sealer should do the trick.
thingiverse
I needed something to connect a Dewalt orbital sander to a Rigid Shop Vac that had a 1-7/8" hose. Printed with PLA at 100% and fits snug. ... TinkerCAD file: https://www.tinkercad.com/things/8555srNBKRV
thingiverse
Just a litte adapter to go from a 1.25 currugated pool hose to a 3/4-11.5 garden hose. Did this so I can use the pool pump to empty out the pool. ...Also see my 1.25 hose adapter to taper on the inlet of the pool hose.
thingiverse
... 1.5 inch ports. I'm adapting this to a 1.25 inch vacuum hose, CRAFTSMAN CMXZVBE38662 to be specific. ... Hopefully this helps anyone that ran into this problem as there seems to be no standard with vacuum hose sizes and readily available adapters.
thingiverse
Created half inch male garden hose threads adapter to 1/2" barbed fitting. Fits Tight. ...Posted F3d file from when I designed with Fusion 360
thingiverse
Garden hose adapter for the [Intex Pool Bayonet Adapter](https://www.thingiverse.com/thing:4421324).
cults3d
But my pump came with a BSP 1 1/4 (1.25 inches) thread, I didn't want to buy some pipes or adapters while lockdown. Use sealant thread tape, and it works perfectly ! (this kind of pump is not made for that use, it lack a little of pressure, but...
thingiverse
> >But my pump came with a BSP 1 1/4 (1.25 inches) thread, I didn't want to buy some pipes or adapters while lockdown. > >Use sealant thread tape, and it works perfectly ! (this kind of pump is not made for that use, it lack a little of pressure,...
thingiverse
... sander dust extraction. ...This replaces the small dust catcher already attached to the sander. The fit should be fairly tight, especially as it goes over the small rubber o-ring. On the vacuum side of things, this fits a standard 1-1/4" vacuum hose.