1.5 mm to inches 3d models
2831400 3d models found related to 1.5 mm to inches.thingiverse
The 5 mm hole is suitable for NEMA 17 stepper motor shaft and the 1/4 inch is for the ACME threaded rod. Now Version 1.1 includes some minor tweaks such as: 1) A middle notch to improve the clamp flexibility. 2) M3 hex nut cutouts to make tightening...
cults3d
Inner diameter is 2.5" two point five inches to 1.75" one point seven five inches. Height is 3" three inches. Wall thickness is 0.15" zero point one five inches. Takes about 5 hours to print. ... If it's a bit tight which mine was use some heat when...
thingiverse
Inner diameter is 2.5" two point five inches to 1.75" one point seven five inches. Height is 3" three inches. Wall thickness is 0.15" zero point one five inches. Takes about 5 hours to print. ... If it's a bit tight which mine was use some heat when...
thingiverse
Collect three vacuum lines - from 40 mm, 2 inches, 2 and 1/2 inches to 4 inches Main part test and print in ASA - (0.6mm. 255C. 115C. 60% in fill, 15 % Fan, CURA DRAFT- 0.2mm lh) Feel free to support my projects!
thingiverse
a bracket for a 2x2 lumber (1.5"x1.5"). ...Mainly used for RC plane Rack.
cults3d
... I use it for my DIY Sling Enclosure from Hobby Lobby. Size is roughly 1 inch wide by 9/16" tall and a 1/4" thickness. ... V2 file just has more bevels (lower profile) Have printed in both Resin and FDM printers
thingiverse
Customized version of https://www.thingiverse.com/thing:267073 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=267073
thingiverse
remix of https://www.thingiverse.com/thing:5571604 shorten each side by 1/2 inch so should be 2 1/2 inch add 2.75 inch side Add 2 inch side also
grabcad
This a brake pedal which has many adjustable options to opt for different size of drivers. ...Its pedal ratio is 5.5:1. ...And its size is 10 inches
thingiverse
These LED holder, allow the light to go in the fiber optic's. ...There are 3 different sizes, for the LED's (1.8, 3 and 5 mm)
cults3d
These LED holder, allow the light to go in the fiber optic's. ...There are 3 different sizes, for the LED's (1.8, 3 and 5 mm)
thingiverse
It is a fan duct dedicated to various application, but it's main purpose is to replace and/or extend a traditionnal 120mmx120mmx38mm fan to a 5 inches piping, such as a 5 inches blower fan, etc. It is designed to fit with the same screws used with...
thingiverse
Bit adapter that has a standard 1/4" (6.31 mm) shaft that goes to a pentagonal (nominal 5 mm side length). 11 May 2017: I messed up the hex dimensions. They've been fixed with updated SLDPRT & STL files. ... 13 May 2017: It was too big on the hex...
prusaprinters
Updates2022/03: Added chamfer to one side for easier insertion of keys (v1.1), made clamping surface area inside the holes slightly larger. DescriptionMetric hex key holder for sizes 1.5 / 2 / 2.5 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 mm. Print...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1324986 Instructions Using the following options: Size_A_barb_count = 4 Number_of_Size_B = 1 Number_of_Size_A = 6 Inline_Connector = round Size_B_barb_count = 3 Wall_Thickness_B = 3...
cults3d
Faucet adapter M18 to 1/2 inches. ...To fit your new aerator
thingiverse
This is a filter adapter in 1"1/14 (31,75 mm) to use Edmund optics filters of 12,5mm diameter. ...The filter holder fits perfectly into any filter wheel, but you'll need to remove a little material (with emery paper,...) to get the EO filter to fit in...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=299663 Instructions Using the following options: height = 30 opening_width = 2 bolt_diameter = 3.5 washer_diameter = 6 diameter_bottom = 5.2 nut_diameter = 6.25 outer_diameter = 20...
cults3d
This is adapter for 3/4" standard water pipe to 30 mm diameter pipe, that I use in my projects.
thingiverse
This adapter fits a 3/4" standard water pipe to a 30mm diameter one, which I utilize in my projects. For high-quality female threading, print at 0.1mm per layer. Compatible with three vacuum sources: hair dryer (print this adapter:...
thingiverse
This is a bed riser that will raise your bed about 1.2-2 inches, depending on the presence/size of wheels. ...It is very strong, and I recommend printing with PETG
thingiverse
24mm to 30mm threaded adapter with endstop. ...Please use high infill and temperature-appropriate filament (do not use PLA for pipes that get hotter than 40C)
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following options: output_units = Metric inline_junction_type = round input_size = .5 strength = 1.0 input_units = US vault_connector_ratio = 1.8...
thingiverse
5 mm motor shaft and 8 mm screw coupler. ...Print Settings Printer: NuBBoT
thingiverse
... project and i tought maybe more people needed it. THIS is not a Z-Axis Coupler. There are a lot on Thingiverse already. This coupler is for a 2.5 mm Motor to a 8 mm rod. Therefore please check before printing if this is what you need. ...
thingiverse
Universal charger DC 6 - 30 volts, 5.5 x 2.1 mm to USB, QC3 The inscription on the body is a through grate through which ventilation is carried out when heated. ... The parts are glued in, the stop is in the middle for rigidity when the plugs are...
thingiverse
Prusa Coupler 5mm to 8 mm more easy to print more robust Print Settings Printer Brand: RepRap Printer: CTC Prusa i3 Pro B Rafts: No Supports: No Resolution: 0.1 Infill: 20 Post-Printing How I Designed This Draw in OnShape public model:...