10 series aluminum extrusion 3d models

I found Bill84s corner bracket and printed out a pair for my new printer but I was going to be using bolts instead of screws so where his support bracket in the back was wouldn't work for me as I couldn't get a socket in there (the irony is after all...

I designed these for 10 series aluminum extrusions that are 1" x 1" square. key differences over others of the same, the nut is twisted to grab mor metal when tightened, and the corners are rounded for easier printing. Long version: As most...

Just stick whatever model you want to attach to the 80/20 aluminum extrusion on top of the plane, and it should pretty much work. This model is probably a hair too big. Some of the extrusions it fits great in, others are a bit tight, so I guess...

<p>I could not find a zip tie mount to hold wiring down that met my needs so i decided to make this. ...The mount hole is for a 1/4-20 button head screw.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>MakerBot</p> <p...

I could not find a zip tie mount to hold wiring down that met my needs so i decided to make this. The mount hole is for a 1/4-20 button head screw. ...Print Settings Printer Brand: MakerBot ...

I designed this brace for 10 series aluminum extrusion which is the inch equivalent of 2020 extrusion. The through holes accept 1/4-20 screws which are the standard hardware for 10 series. ... I am not sure if this brace is compatible with 2020...

I designed this part for 10 series aluminum extrusion which is the inch equivalent of 2020 extrusion. The mounting holes accept 1/4-20 screws which are the standard hardware for 10 series. The motor mount is for a standard nema 17 stepper motor....

I designed these parts for 10 series aluminum extrusion which is the inch equivalent of 2020 extrusion. The mounting holes accept 1/4-20 screws which are the standard hardware for 10 series. The motor mount is for a standard nema 17 stepper...

This is a foot designed to fit 80/20 10 series aluminum extrusions. It was originally made for a car roof rack, but it can be used as a general foot/support, or modify it for your needs! Be sure to print it on it's side so the layers run through...

Wasn't 100% happy with all the twist in wire holders I was finding, so made a simpler low profile version to work with 40 series aluminum Extrusions. Depending on the aluminum manufacturer these can be a very snug fit, as in you may need a pair of...

I built this model to assist me in designing printable mounting and joining hardware for T-Slot (ultra light) extrusions. It will also come in handy in allowing me to use it in my models to visualize more complete assemblies which will make use of...

... will help keep your wires out of the way while being easy to install. You simply insert it into the T-Slot and twist. It was designed for 80/20 brand Series 20 T-Slot extrusions, but will work with any t-slot extrusion that has similar dimensions.

This is a simple remix of the Valve Index Controller Wall Mount that can be mounted to a 40 series aluminum extrusion with a single M8 bolt.&nbsp;&nbsp;Additional Items Required:&nbsp;M8 boltM8 T-nut

This remix is of 15° Logitech MX Ergo trackball mouse base that will bolt to 40 series aluminum extrusion with 2x M6 bolts. You can use Industrial Strength Velcro Tape to mount the mouse to the base. ... Additionally required: 2x M6 bolts 2x M6...

This is a remix of darknao's 15 degree Logitech MX Ergo Mouse Base (https://www.thingiverse.com/thing:2640807) for 40 Series Aluminum Extrusion. It can be mounted with 2 M5 bolts. ...It's recommended to use Industrial Strength Velcro Tape to mount the...

Aluminum Extrusion

This is an alternate hanger for use on horizontal 8020 series 1010 extrusions. It clips into the extrusion and makes it easy to hang an ornament or a utensil from the extrusion. Unlike the last one which held the dangling item at the front of the...

This will allow the belt guide rollers to be mounted to 40mm aluminum extrusion for belt tensioners used in sim racing and flight simulators. The 45 degree angle was utilized to provide a wide range of clearance options depending on the placement of...

This clip is twisted 90 degrees to allow routing in a different direction and has a larger rounded top to allow for more wires and the use of cable sleeves.Once printed, fit the small section into the extrusion t-slot and then twist to lock into...

This clip has a larger rounded top to allow for more wires and the use of cable sleeves.Once printed, fit the small section into the extrusion t-slot and then twist to lock into place. ...A side opening on the clip allows for a little flex to insert...

This clip has a larger square opening to allow for more wires or cables.Once printed, fit the small section into the extrusion t-slot and then twist to lock into place. ...A side opening on the clip allows for a little flex to insert...

30x30 aluminum extrusion

Aluminum extrusion Die

... together with socket head cap screw 1/4-20 x 1/2. ...I use this to make a enclosure with aluminum extrusion.   Print in PETG for stronger parts. ...The top hole is filled with a 0.2mm layer that you just need to remove with the bolt or a knife.

Inspired by rlspell's http://www.thingiverse.com/thing:17194, this drop-in has been modeled from scratch to fit all 8020 Series 10 extrusions. This nut can be dropped in and locked in place with a #10 screw.Safety Disclaimer: This is only for...

Standard Extrusion sizesMultibody part using Solidworks

A adapter for attaching a pice of 8020 series 10 extrusion to the post on a wire shelf.

Arca-Swiss Style mounting plate to 8020 series 10 style extrusion. ...This is a quick adapter for devices that use a 8020 series 10 style extrusion so that they can be used in a tripod that supports a Arca-Swiss style mount.

Arca-Swiss Style mounting plate to 8020 series 10 style extrusion. ...This is a quick adapter for devices that use a 8020 series 10 style extrusion so that they can be used in a tripod that supports a Arca-Swiss style mount. Category: Camera

A mount for an Adafruit caster bearing wheel for use with 8020 series 10 extrusions. (https://www.adafruit.com/product/3949) Three different hights are provided to match with wheels by Adafruit and Actobotics. (It's what I had laying around. ...) It...