10 x 10 games 3d models
840500 3d models found related to 10 x 10 games.thingiverse
This is a smaller 10 x 10 board game challenge. It is a 2 x 10 w/ 4 x 5 challenge. It has two games at 10 plays a piece, and four games at 5 plays. Use a brim or raft when printing as this will take up a large portion of the bed. No supports are...
thingiverse
Customized version of http://www.thingiverse.com/thing:41108 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=41108 Instructions Using the following options: width = 10 thickness = 1 length = 10
thingiverse
Customized version of http://www.thingiverse.com/thing:50437 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=50437 Instructions Using the following options: Block_Width = 10 Block_Length = 10 Block_Height = 1
thingiverse
... version of http://www.thingiverse.com/thing:1038261 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1038261 Instructions Using the following options: zScale = 10 xTranslate = 50 zRotation = -45 wholeMessage = /x/
thingiverse
This is a simple games rack that i designed for holding 10 games at a time. ...Ive made one with the playstation logo, one with the xbox logo and one without a logo.
thingiverse
This is a quick designed gameboy game holder for display reasons. ... This print will hold 10 gameboy, gameboy color, or gameboy advanced games. ... It is designed to look simplistic but good on a shelf.
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=132939 Instructions Using the following options: edgeSupports = 2 columns = 10 LEDdiameter = 5 WallThickness = 1 BasePlateThickness = 2 rows = 10 spacing = 3 height = 8
pinshape
A good idea is to purchase rubber feet that typically are seen on the bottom of jewelry boxes and place them on the bottom of this XBOX game holder. They usually sell them at a hardware store. ... SPECS ========================== ...
thingiverse
Customized version of http://www.thingiverse.com/thing:50437 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=50437 Instructions Using the following options: Block_Height = 2 Block_Length = 10 Block_Width = 10
grabcad
this will carry a golf buggy or similar - 10 ft x 6 ft inside trailer with 2000 kg tandem axles - ford ranger wheels
grabcad
dia 23 inch x 10 inch pitch with 2° angle of attack added to the bladeI am going to try this prop on my aero tow plane. the motor is a 60cc twin cylinder DLE. ...we are towing up to 12kg models to 1000ft in 40sec.
cults3d
Why are you looking for description? ...This model is self explanatory. HAha joke, it's a character from Ben 10 series, the most powerful one: Alien X. I recommend you to watch this amazing cartoon. ... About the price: I worked on it for 5 hours.
thingiverse
This is an x-carriage for the CR-10. It is made for 2pcs 50x15 blower fans. It also uses a 30mm fan for the hotend cooling. All screws is M3. I use M3 loc nut behind the hotend. So far it is working fine, and the cooling is really good. The...
thingiverse
... http://www.thingiverse.com/thing:260104 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using the following options: height = 10 padding = 1 number_of_columns = 5 diameter = 10 number_of_rows = 2
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=15633 Instructions Using the following options: length = 30 boltShaft = 3.5 thickness = 4 washer = 0 gap = 0.3 shaft2 = 10 shaft1 = 8 trap = 2 wall = 1.6 bridge = 0.3 offset = 2 boltHead = 6.7...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=493228 Instructions Using the following options: cellheight = 3 cellthick = 0.8 cellrad = 3 overlaptype = yes cols = 5 rows = 10 celltype = open
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=57281 Instructions Using the following options: _columns = 4 _labelHeight = 8 _base = 0.8 _fitGap = 0.1 _labelDepth = -0.3 _labelText = _labelFont = write/orbitron.dxf _lipHeight = 2 _walls =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=15633 Instructions Using the following options: shaft2 = 10 shaft1 = 6 trap = 2 gap = 0.3 wall = 1.6 offset = 2 nut = 7.8 length = 30 thickness = 4 boltHead = 6.7 bridge = 0.3 washer = 0...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_type = normal head_height = 5 facets = 6 nut_thread_step = 1 drive_type = socket type = bolt non_thread_diameter = 0 slot_width = 1...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: slot_width = 1 thickness = 2 resolution = 0.5 inner_diameter = 8 thread_step = 0.5 thread_outer_diameter = 3 step_shape_degrees = 45...