13 inch to mm 3d models
2213580 3d models found related to 13 inch to mm.thingiverse
... for a leki skiing stick. ...The diameter of the hole is ca. 13 to 13.5 mm and its length is 20 mm. The whole has a outline that will stop him from deducting. You will have to fix it on the stick with pressure. ...If you heat it fixing will be easier.
thingiverse
I had problems printing this thing because the stl was saved in inch. ... A simple multiplication of the size with 254 (100% -> 2540%) gives you the mm version.
cults3d
Modified to allow vented connection to 4" dryer hose pipe for use with a custom airbrush paint booth. ...Left the wider secondary exterior ring to allow for good overlap seal using HVAC reflective tape.
thingiverse
Modified to allow vented connection to 4" dryer hose pipe for use with a custom airbrush paint booth. ...Left the wider secondary exterior ring to allow for good overlap seal using HVAC reflective tape.
thingiverse
This is all of the gears T5 from 21 to 30 teeth 13 mm high and 13 mm central hole. ... Supplies for all sorts of ratios for the gears.
thingiverse
This is a list of gears for T5 Belt with 13 mm center hole flanges and 41 to 50 teeth This is essentially 1/2 inch center hole. ...
thingiverse
This is a list of 10 gears. ...31 teeth to 40 teeth for T5 Gear with 4mm flange and 13 mm center hole all ready for 3D printing
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=69655 Instructions Using the following options: Tool_Length = 10 Nut_Size = 13 Font = write/Letters.dxf DualExtrusion = Extruder1 ToolOptions = 2 kerf = 0.3 message = 13 mm
thingiverse
... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=69655 Instructions Using the following options: Tool_Length = 10 Font = write/Letters.dxf ToolOptions = 2 message = 13mm Karlijn DualExtrusion = Extruder1 kerf = 0.3 Nut_Size = 13
thingiverse
Simple, quick and dirty adapter from 33,24 mm thread on pumps side to 25 mm inner diameter hose.
thingiverse
This will help you to transfer your ants from a test tube (13mm) to a bigger test tube (16mm) in case the colony is getting bigger, or you´re running out of water. ...It also has small holesfor air circulation.
thingiverse
I am doing some crazy ducting and would like my pc to blow air into two 4 inch pipes so I made this. ... v2 has a smaller 4 inch output to accommodate overlap but V1 is best route.
thingiverse
It is suitable for all manufacturers with 13 / 13.7 mm piping, I use it with the Gardena Micro-Drip system (naming rights with the manufacturer), but there is absolutely no connection or support to the manufacturer. In addition, I could not find a...
thingiverse
This thing provides support sockets, you can use the rear rings to hang the wall mount.
thingiverse
II grew up suing the imperial measuring system and still think in those units. ...But, in cad design I work in the metric system. I made this simple slide to allow me to convert imperial to metric on a ruler to .5mm
thingiverse
This is still very much a work in progress based on Simon's original design Not yet ready for production Thanks to Simon for his original design
prusaprinters
This is a 13 mm to 13.7 mm hose connector / adapter.I use it with the Gardena Micro-Drip system and connect the 13.7 mm drip hose (underground) with the normal 13 mm laying pipe.This allows you to interrupt the underground drip hose over longer...
thingiverse
I managed to print it on the first try in PLA, with 0,2 mm layer height and a 0,5 mm nozzle. Regarding the functionality it is waterproof and works but the part wasn't really pretty due to the bridges. ...Therefore I recommend printig this part with...
thingiverse
Also included 13mm ( x 2) stands to be used with the gauge, cause the absolute 0 of the gauge are 13 mm. ...https://www.youtube.com/watch?v=f2yUqLVQL0Q&t=4s Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.25 Infill: 15% zig zag...
thingiverse
This is an adapter for connecting two standard 13 mm Gardena water hoses. Depending on your setup scaling may be needed for best fit. ... Printed in PLA on a Reprap Neo, 0,2 mm layer hight and 0,5 mm nozzle, works good so far :)
grabcad
Downloaded a 13 inch rim and tire model here with the folder name "keizer_13_in_rim_tire", and improved the tire by adding tire tread and embossed text on side walls. Upload the new tire file to contribute back to the group here. ...Kudos goes to the...
thingiverse
I slightly modified motoi1484's Apple Magsafe2 holder to fit my 13 inch late 2012 Macbook Pro Retina 13 inch model. This object is to be used with a MagSafe to Magsafe 2 Converter like...
cults3d
PE DIAM from 9 to 13 mm and double CABLE TIGHTENER