14mm to 17mm hex adapter 3d models
2181418 3d models found related to 14mm to 17mm hex adapter.thingiverse
Hex Adapter for rc car wheels 17mm to 12mm (the ring for the rim has 12,5mm) The Adapter gives a few mm of offset.
thingiverse
This adapter allows you to use a 17mm hex wheel on a 1/10 scale rc truck. it adapts the 12mm hex to 17mm. You will need a washer bigger than 17mm to keep the wheel in place with the stock 12mm nut. ...Works great and is tested with traxxas 1/10 scale rc...
thingiverse
This helps use 14mm hex wheels on 12mm hex vehicles. fits 6mm wide hex. ...Great for using Arrma wheels on other cars.
thingiverse
made this to be able to fit 23mm HEX rims/wheels to a RC car mde for 17mm Hex. ...The hole in middle is 12mm Hope someone needs it, my friend did, that's why I made them =)
pinshape
Summary made this to be able to fit 23mm HEX rims/wheels to a RC car mde for 17mm Hex. ...The hole in middle is 12mm Hope someone needs it, my friend did, that's why I made them =) Instructions Print them solid, propably best in ABS or Nylon, no...
thingiverse
This will allow you to install Traxxas X-Maxx wheels on a Traxxas Summit RC car.
thingiverse
Needed a adapter for my stampede to except the dboots ragnarock tires. ... this will go from the 12mm to 14mm
cults3d
This is an adapter for using a 17mm hex wheel with a 12mm hex on an RC car. Obviously plastic is not ideal but if you are in a bind this will get you going. The adapter goes over the 12mm hex on your car and the washer goes on the outside of the...
thingiverse
This is an adapter for using a 17mm hex wheel with a 12mm hex on an RC car. Obviously plastic is not ideal but if you are in a bind this will get you going. The adapter goes over the 12mm hex on your car and the washer goes on the outside of the...
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/cwovWkc767P
thingiverse
Rc car/truck 17mm to 20mm hex Print Settings Rafts: No Supports: No Resolution: 0.2mm Infill: %100
thingiverse
Created in response to a request for an 11mm to 14mm adapter. ...Inner thread is 11x1 (both + and - files are included), while the outer thread is 14x1-.
thingiverse
I've acquired a set of Traxxas Slayer wheels and noticed they didn't fit the 12mm hex of my Traxxas Slash 2wd beacause they were 14mm Here are two different adaptors:
cults3d
A simple adapter with smooth inner taper suitable for cpap systems and other needs where flow cannot be restricted.
prusaprinters
A simple adapter with smooth inner taper. Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports: NoResolution: 0.1 Infill: 15 Filament: Generic PLA Black Notes: For best fit, print at highest resolution. Category: Parts
thingiverse
depending on your printer mite need to adjust slightly, print it the other way up !
thingiverse
print horizontal adapter 14mm cw to 14mm ccw horraire vers anti horraire 0.75 pas de vis (de tête mais fichier modifiable au besoin)
thingiverse
17mm hex adapters for the Tamiya Bruiser / HG-P407 RC Truck.
thingiverse
this will covert any rc car that uses a 14mm wheel nut to a 17mm which allows many different types of wheels to be used
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/cwovWkc767P
thingiverse
14mm int / 17mm ext hub adapter for RC truck, truggy, buggy... ... I print it with flex filament from Hobbyking hotbed 50° extruder 195° enjoy!
thingiverse
Sizes : From 6mm to 17mm Estimated Print time @ 70mm/s : single bit : from 1 to 5 mn small set (6 to 11mm) : 15 mn big set (12 to 17mm) : 25 mn These are just tool bits. If you need a handle or other tools for your bit holder, visit :...