2.5 to 3.5 ssd adapter 3d models

2.5" SSD hard disk adapter for 3.5" bay mounting (HDD IDE/SATA bay) It can also be mounted in the 3.5" floppy disk bay.

2.5" SSD disk adapter for 3.5" mounting Size 100mm by 17mm Increases your magnet by 86 if you print it in red.

SSD mounting holes are not made through for better printing results. You just need to break through it. ...It's thickness is only 0.2 mm, so it is not difficult.

2.5" SSD hard disk adapter for 3.5" bay mounting (IDE/SATA HDD bay) It can also be mounted in the 3.5" floppy disk bay.

2,5" to 3,5" SSD/HDD adapter

This is a remix of the 2,5" to 3,5" HDD/SSD adapter by Tadziurski. ...Added a third mount hole as my case did not provide the outer most one.

This is a remix of my own design, complemented by nine more variations. ... Note that SSD mounting holes are not made through for better printing results. You just need to break through it. ...It's thickness is only 0.2 mm

Very simple and minimalistic 2.5 inch HDD or SSD to 3.5 inch adapter

Very simple and minimalistic 2.5 inch HDD or SSD to 3.5 inch adapter

Using Fusion 360, I designed this adapter to mount a 2.5" SSD into a 3.5" drive bay. I then 3D printed it using an Ultimaker 2+. ...This was specifically designed for a HP Z420 Workstation but should work with any computer.

I needed this adapter to mount my new SSD, because I don't have a 2,5' slot in my computer case. ...I printed my adapter with white PLA, but ABS or PET-G might be better for it (greater heat resistance) Designed in Autodesk Inventor 2017

This is an adapter to mount a 2.5" SSD into a 3.5" drive bay. My specific use case for it was to mount in a Rosewill 4500 4U case so the holes are not threaded. There is probably enough space to fit 2 SSDs in the space occupied by one 3.5" drive...

Adapter to hold 2x 2.5" drives in a single 3.5" bay. Remixed from [Tadziurski's](https://www.thingiverse.com/tadziurski/designs), original design [here](https://www.thingiverse.com/thing:1942247). ... solid state hard drive adapter

Tried to created an all in one 2.5" to 3.5" adapter bracket that does not require extra screws to hold smaller drive in place. ... Any helpful comments are welcome.

Adapter to mount 2.5" drives in systems that are designed for bottom-mount 3.5" drives. This is particularly useful for various systems that use drive trays/sleds - I'm using one of these to mount a 2.5" SATA drive in an old Macintosh Performa 630.

I could not find the right adapter. ...That's why I designed this for my "be quiet" case. I tried to keep it as simple as possible. It should work for other 3.5 "bays of course.

That's why I designed this for my "be quiet" case. I tried to keep it as simple as possible. It should work for other 3.5 "bays of course. Print instructionsCategory: Computer Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports:...

This design is an attempt of converting mounting holes of 2.5 inch disk drive to 3.5 inch form factor. The SATA interface port should remain in the same place which is useful for upgrading your old ALL in One PC with a SATA port connector fixed. ...

... extra holes to acomodate for Floppy drive bay installation. ...-original only supports 3.5 HDD bay. Side walls now have full enforcement, via 45 degree bracket. -much stronger and better longevity. ... Recommended for use with fine-thread screws.

Based off http://www.thingiverse.com/thing:168750 by Clax, after I made one I realised I needed the other two mounting holes on a 3.5 HDD to fit my drive bays in my Antec P182 case. ... This is the result!

Virtually all 2.5" to 3.5" adapters place the 2.5" drive such that the 2.5" drive's SATA connector sits where the 3.5" drive's connector would. This works great if you're using SATA drives in a SATA system, but it can be problematic if you're...

2.5" to 3.5" HDD/SDD Hot-Swap bay adapter for CoolerMaster Silencio 550 (maybe fits in others...). Based on this idea: https://www.thingiverse.com/thing:4797411 Screws are the same. ... For me more comfortable for using, easy to print.

Here are several versions of drive bay adapters to mount a 2.5" drive (SSD or noteboot HDD) into a 3.5" drive bay. Update 2021-11-09: Added a version of the larger mount with sunken screw heads to install the mount also at the very bottom of a drive...

This is an adapter to assemble a 2.5", 7mm SSD into a 3.5" disk bay. I have an Fantec Raid 4x enclosure, where this fits perfectly in. Prints with no additional adhesion (brim/raft). The support can be easily removed with a plier. ...(shown pink in one...

2.5" Drive to 3.5" Drive Adapter. Should fit most applications. ... Super simplified, reversible, and thin for ease of printing.

simple 2.5" to 3.5" hdd adapter with 3 holes. holes align up perfectly. ... print in ABS to reduce chance of plastic warping once installed into a pc case.

... While I was at it I added the SSD bottom screw holes to allow it to mount either. Depending on your cases screw holes, you might be able to stack 2 of these in 1 slot, but I found at least 1 case that it didn't, so you can check that on your own.

Mount adapter for two max 10mm thick 2.5" SSD to fit into 3.5" bay. Mirror the part for another side. ... Photos © Jere Siirilä

Took about 36 minutes to print 2 of them on an Original prusa Mk.3 Depending on material, be careful when screwing in the screws meant for 3.5", the bracket is designed for them to self-thread, so excessive torque with a brittle material may break...

Remix: Correct screw spacing. ... Allow for inset screw heads with print supports designed in the STL. Less material used in the bottom. Various options for side and/or bottom adapters for the 3.5 inch drive.