2.5 to 5.25 adapter 3d models

SSD 2.5 to 5.25 adapter

A revised adapter, measuring from 2.5 to 5.25 inches, was developed following the design available at http://www.thingiverse.com/thing:10519

The adapter lets you install two 2.5-inch SSDs inside your HP workstation case's 5.25-inch bay. No screws are needed to mount the adapter in the case - just insert it into the grooves and secure with the original latch. Each SSD is attached to the...

I separated the original into two equal parts so that it could fit neatly within a 5.5-inch wide printing area.

So i designed a small 5.25" drive bay (2 5.25" bays high) that can store up to 6 2.5" drives and 1 80 mm x 80 mm fan for ventilation. Drives are just "pressed" into the cages. After testing 8 different drives all nicely fit to the knobs on the...

Adapter to hold 2"5 or 3"5 HDD drives into a 5"25 CD Rack Dimensions and screw positioning are based on Standard specifications. ... The source file is an Openscad file [avalaible on...

Adapter to hold 2"5 or 3"5 HDD drives into a 5"25 CD Rack Dimensions and screw positioning are based on Standard specifications. ... The source file is an Openscad file avalaible on github In order to execute it you need Basic Prerequisites

... v1-1. Sorry about the inconvenience. Update: I've just uploaded v1-1 with horizontal holes for effortless mounting of a 3.5-inch hard drive. ... If you found this useful, I'd be grateful if you could treat me to a beer at http://paypal.me/pabile.

... free to point out any areas that need improvement and share your feedback freely. A detailed write-up about this updated version is available on my blog at this link. I'd love it if you could check it out and share your thoughts. ... Stay safe!

Adapter to make 2 SSD's and a HDD fit into a CD drive space

The Adapter Master allows for the installation of two 2.5-inch hard drives within a standard 5.25-inch drive bay, making it an essential component for those seeking to maximize their storage capacity and versatility. ...Two units are required for...

To reduce the plastic left only a corner

To reduce the plastic left only a corner

... While I was at it I added the SSD bottom screw holes to allow it to mount either. Depending on your cases screw holes, you might be able to stack 2 of these in 1 slot, but I found at least 1 case that it didn't, so you can check that on your own.

Very basic adapter to mount two 2.5" SSD drives in a common 5.25" drive bay. You can use the modifier mesh to remove top and bottom surfaces in those areas and save both time and filament. ... It uses M3 screws and nuts.

I needed to add as much as possible HDD to a home server so I made this adapter to add 8x 2,5'' drives to a 3x 5,25'' drive bay.It is designed so it can hold drives up to 12.5mm hight and drives can be either just placed in place or you can use screw...

this is the STL from my youtube video to mod your case: https://www.youtube.com/watch?v=LUvsZnAJXcw print flat as seen in the Cura screenshot. no support needed. infill of 25% is recommended. ... PLA is good enough.

Simple Storage Solution Boosts 2.5" Drive Capacity at Home and in Small Offices. This solution is compatible with drives of both 9mm and 7mm height, making it a versatile option for various storage needs. However, due to limited thermal...

Based on http://www.thingiverse.com/thing:345435, this adapter fits snugly into the standard 5.25'' CD-ROM bay, making it compatible with both 2.5'' and 3.5'' hard drives, including SATA, SSD, or IDE models. Instructions: Ensure that your infill...

I hawe old "but good" pc case with no spaces for 2.5" drives. ...You hawe to drill holes for discs with 3,5mm dril.

This remix is a redo of the original file:\r\nhttps://www.thingiverse.com/thing:858533\r\n\r\nThe original file had a wrong scale, but it was built using a rescaled modification as its base:\r\nhttps://www.thingiverse.com/thing:1607776\r\n\r\nEven...

Accommodates five 2.5" hard drives into a single 5.25" drive bay (opted for five in order to have some space for air between the 2.5" drives. Modeled using the blank of a HP Z6 G4 workstation. Use flat headed screws for installing top and bottom...

Adapter/Cage to hold 10x 2.5" SSDs or HDDs vertically in place of two 5.25" bays. Can be mounted in various depths depending on your case. ... This is a slight edit of Sir_Yaro's design: - Added additional holes so that it can mount to both 5.25" bays...

Just scale the design to a perfect size, so you can easily download and print it out. Print Settings are what matters most here. Rafts are irrelevant when it comes to printing. Resolution is critical - set it at 0.2mm for a crisp finish. ...Infill is...

I struggled to find an adapter that fit perfectly for me, so I quickly created this 5.25" drive bay to 2.5" SSD / HDD adapter from scratch. Two drives can be stacked together, and standard mounting screws should work just fine. I used M3 button head...

I made this for myself because I hated the SSD just floating around in the case. As is. I printed it on a stock Ender 3 pro, 0.4mm nozzle with PEI bed. No support required. ...Enjoy.

I wasn't able to find a suitable replacement adapter for the Ridgid floor attachment specifically so I was able create one based on the original. ...No scaling required, supports are required.

A front panel adapter to install 3.5" panels in a 5.25" slot on desktop computers.

I had to figure out a way to fit a 3.5 inch drive into a 5.25 inch slot, so I built a tiny adapter.

Compact PC Add-On: Mount a 3.5-inch Hard Drive Inside Your Desktop Computer's 5.25-inch Bay Mount a 3.5-inch hard drive inside your desktop computer's 5.25-inch bay with this handy adapter. ...Perfect for adding more storage space to your system, this...