20 foot extension pole 3d models

I have a 20 foot extension pole, and this is perfect! turn on gopro wifi, and check it on your phone from the ground, No more dragging the ladder around and setting up. This is a remix of GoPro Pole Mount by bmoren with a threaded bolt made using...

A simple pole foot is designed in Solidworks and Autodesk Inventor.Courtesy : Prof. C. ...Stancescu

Just an generic pole threaded on both ends, print multiple to thread together for longer reach.

20/20 profile foot with or without square

An adapter to connect plainolddave's superb rattle can pole holder to extension poles with standard acme thread connection

I've got an aluminum extension pole and bought a window scrubber to use with it. Naturally, however, every manufacturer wants you to use their pole, so the attachment did not fit - the threads are far inside the handle and the pole does not fit...

I've got an aluminum extension pole and bought a window scrubber to use with it. Naturally, however, every manufacturer wants you to use *their* pole, so the attachment did not fit - the threads are far inside the handle and the pole does not fit...

I built this to hang ornaments on my tree outside, using a standard painters extension pole (5 TPI threads). The hook part fits tight into the hole without glue (for my printing setup). This object was made in Tinkercad. ...Edit it online...

I don't have a tall enough ladder but I do have an extension pole with one of those gizmos to change light bulbs on the end. Took some measurements and the head from my wife's Swiffer cleaner and was able to whip up cleaner I could use for that...

Place the part on the wall with a couple of screws and snap the extension piece into place.

If you rotate the pieces around everything can be printed without support except for the socket - 20% infill and wall thickness of 3 will give it a bit of strength. Add a 1" broomstick and use a small screw or a nail to hold it in place. ...Tie on...

A cap to place on the bottom of a pole to protect the ground and its carry bag from ripping. ... Instructions I made this foot cap because the old one cracked. ...It is pretty simple.

I measured up the shortcoming ( it was by 38 mm ) and quickly came up with a simple extension piece to the closet-rod that could be strong enough to take up the load and make it usable. Check out attached FreeCAD files and feel free to customize...

Simply insert you ID card and extend the pole and you now have about 750mm of extra reach! The tolerances on this are a little tight, so I've included the STEP file should you need to make changes. The threaded portions (Cap, first 12mm of...

Simple foot for your festivus pole :) Print in spiralize/vase mode with two bottom layers and nozzle size of your choice. 0.4mm and above is recommended. ...Choice of material doesn't really matter ;) Fill 'er up with sand or similar for added...

A foot for a pole in wargaming terrain, such as the legs of a water tower. The neck has been sized to accept a 10mm dowel but has comfortable tolerances so it should work slightly smaller or larger (~9mm--11mm). This can be printed easily with no...

Needed new Canopy Pole "Feet" and decided to make my own in Fusion 360. ...Work great!

Simple machine foot extension to raise my Tronxy X5SA up another 25mm. Reuses existing rubber foot. Uses 4 M3 30mm and T Nuts to attach. Print inverted with no supports. 15-20% infill. ... Should work on any printer with similar sized feet.

Simple foot extension made for the low cost lighting tripods found on amazon

The stock foot is around 4.35 mm high, so a 12mm foot extension gives 16.35mm clearance. With 16mm+ clearance people with the 92mm Asetek AIO may be able to setup a push/pull config with a 92x14mm fan mounted externally. Pictures show the 12mm...

One of my first Designs for my Bedinge Couch in my Workspace. ...I need the Foot extension to let my Roborock S5 clean underneath it.

My vacuum bot kept running up the foot of the table leg like a ramp, so I created an extension to prevent it.

Foot for awning pole

Extension foot for the elegoo mars printer. This allows a better air flow. You will need 2 inches screw (4). ...If the screw fits too tight, you can use a 1/4 drill bit.

Inspired by the Robert Murray-Smith generator, I bought 20 magnets so re-designed for 20. Uses skater bearings and a 8mm x 200mm stainless shaft. ...still waiting on enamelled wire to do the windings.

Electricity poles model built in Blender and rendered with Cycles, with PBR materials, Game-Ready. The setup is built of 3 poles with cables between, ideal for seting up arrays. File formats: -.blend, rendered with cycles, as seen in the images;...

Electricity poles model built in Blender and rendered with Cycles, with PBR materials, Game-Ready. The setup is built of 3 poles with cables between, ideal for seting up arrays. File formats: -.blend, rendered with cycles, as seen in the images;...

Foot extension for a FlexiSpot desk. Made this for my desk to offset the slope in my floor. Old house built in 1894 It fits snug, no glue or screws. ... Made with a good size lip so height can be adjusted by reducing/increasing Z

This is a device to extend a piano foot pedal to allow individuals with weak leg muscles the ability to more easily depress the pedal. It is assembled with a 1/4-20 nut and 1/4-20×1.75" hex bolt. The pedal is designed to have the nut printed into...

54mm extension for the feet of COMFEE dishwashers. ...Might fit other brands too, check pics for dimensions