20 ft container 3d model

... Lysippos around 330 BC. Alexander is shown looking upwards, as if to challenge the gods themselves. This vision of the inspired ruler, widely copied by Alexander's successors and imitators, became a standard model for Hellenistic royal portraiture.

Dual Output Version Thanks for the CAD models: Banana jacks by Jeroen Lodder Switch by Edge DC jack by Muhamad Sidiq BOM: Find the tip size of your wall-wart/AC adapter before buying the DC jack. Links for 5.5mm x 2.1mm as well as 5.5mm x 2.5mm are...

... Very basic stress testing was done in Fusion360 with a model of a 1.5" PVC pipe sleeved over the mount and it seems like it won't snap too easily. In real life testing, it holds a ~7lb antenna easily. ... Category: DIY

idk what slicer or print settings were used on the original print, but I had to redo the entire geometry of that area to get it to print right without disturbing the bevel of the rest of that model. Unfortunately, given I don't have the original...

Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to six 8mm x 3mm magnets per portrait frame. I...

...• Can readily accept multiple makes and models of components. • Easily modified. (* Flight time based on 3000mah battery) When starting out, long flight times take the frustration out of learning without changing batteries every couple of minutes.

Im Modell seht ihr hier einen auf der Innenseite des rechten Korpus-Teils als Beispiel.Montageanweisung:Der Hauptteil des Korpus, das Oberteil und die beiden Seitenteile werden miteinander verklebt. Auch das Herz Logo wird in den Ausschnitt am Deckel...

The new and improved lock nut can be found here:https://www.printables.com/model/602441To allow for quick turning of longer strews, this design also features a free-wheel at the end, that rests comfortably in the palm of your hand. Optional variant...

Print in your favorite color and put stickers on the flat front, or model a raised logo in tinkercad, and position it on the front with a manual color swap (see dragon and sea monster links below for examples). There are two versions here. One is...

Within this virtual environment, the Brain Tree's neural networks are modeled after those found in the human brain, allowing for realistic simulations of cognitive processes and emotional responses. By leveraging these complex systems, Elite...

[Medium Sized Model - 25mm Base] [Presupported in 32mm and 75mm scale]   A Wastewalker Ranger who was a renowned scout and hunter for the Boundless Wind Clan of Eastern Oldavor. Strika was said to have single-handedly slain a Nix Centipede, and...

... can have its own PTFE tube, and said tube can be looped back out of the way. This is my favorite and very handy to have.IIRC I also increased the size of the dividers between spools and at the end, but it shouldn't affect how the model prints

But even when done well, the model wouldn't withstand a bump or a shaking table. So this one includes an open pocket in the bottom of the "splash" design so that a weight can be glued in there. The weight I used and designed around is a stack of 3...

... face a bit. Other than that I am really pleased with how the design came out and I hope a few people will like it. If you print one of those clocks, feel free to post an image of it. I love seeing what other people do with my models. ... Cheers :)

If you wanted to use the TPU ones you can source from original model.All parts moved on to one build plate and designed to be used with the AMS that has 5 slots spaced about 40mm apart.I also have a couple of assemble notes:Pop a screw through the...

Print the model 2. Remove the heat sink, tubes, retaining screws, and any heater or thermistor -- only the hot block and heat break should remain 3. If assembling, thread heat break onto hot block and finger tighten 3. Turn hotend and jig upside...

There are five models. The I/O panel, a fan holder to go with it, and a small extension for the spacer at the HDD bay (2nd pic shows where/how to use it). Also added the original standalone fan holder from before the decision to make a replacement...

about a week getting all the hair right, and that was even after borrowing a low poly hair off google, which only had 2 sides of a triangle for each hair piece (useless) so used the snake hook tool to copy the hair in zbrush and pull it around the...

... Shy Dry Dock (4096x3072px Animated MP4) - Once Bitten, Twice Shy Resources- Olivian Isles Map, Port Oliva Map and Wedding InvitationCompatible .STLs available. Fully Playtested. Part of the Kickstart Smash-Hit "Magnificent Maps, Modules and Models."

The asymmetric planetary gears by faggahz caught my eye, as did the eccentrically cycloidal drive model by otvinta3d - but neither quite seemed to hit the mark. So it made perfect sense to connect them together and see what I could come up with. I...

**New mounting point** If you want the improved mounting point, you can choose between a file with modelled threads to just screw in the thread insert (if your printer is accurate enough, for me it worked flawlessly) or a file without the threads,...

Print Settings Printer Brand: Printrbot Printer Model: Simple Black Rafts: No Supports: No Resolution: 0.3mm Infill: 15%-25% Notes: I recommend using at least 3 perimeters because the screws may crush the plastic otherwise. I used 4 to ensure a...

These pieces are intended to be a friction fit but may require glue depending on your printer's specifications and how you plan to use the model. The smallest recommended scale is 200% (the files are small due to Inventor's exporting limitations),...

My model is fine enough so there's no need to print another yet. If it's too snug for you, and you have Fusion360, you can adjust the clearances on the Fx Parameters page.\r\n\r\nHUGE THANKS to Domestic Hacks for providing the starting point for this...

Be sure to check out my improved design that features a low B-flat hole: https://www.thingiverse.com/thing:4572413 Version 3.7 fixes a flaw in earlier versions that affected the alto model and caused holes below the middle of the instrument to not...

It's controlled by an Arduino UNO over a bluetooth connection from your smartphone.Part one in our series covers the majority of the electrical assembly, and the creation of his main body.https://www.youtube.com/watch?v=qFbfLk-jUd4Here us the second...

This is a Tilt stand hold and align an iPhone 12 Pro Max with a Belkin "Boost Charge" Wireless Charging Pad 15W (model number WIA002). It is best connected with some right angle usb-c adapters.</p><p>This stand holds the phone at a 60 degree angle,...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with...

Technically speaking, this was modeled after a traditional one-handed Javanese Kris sword. But to my knowledge, a double handed version never existed in real life and the weapon was a symbol of societal status. I liked the curves, and one day would...

#Updates:# ________________________________________________________________________ Update July 17th: Added Eccentric_Nut_Custom-Tool.zip to replace stock Eccentric Nut with larger model to help against deforming, you can use Drill jig on your...