2015 drz400 3d models
47722 3d models found related to 2015 drz400.thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=362391 Instructions Using the following options: text_allignment = embossed text_font = orbitron.dxf text_size = 8 text_itself = DRZ400 show_text = yes
thingiverse
A complete braket to mount an EBAY/Alibaba LED stlye 6x4 headlight on the DRZ400
thingiverse
A alternate to the engine breather box fitted to the DRZ400. ... This box can be removed with the exhaust in place.
thingiverse
Suzuki DRZ400, probably supermoto. One of models is little bigger, to compensate for wear on the steel screw (gear). When printing with nylon, I enlarged the model in a slicer. Large material shrinkage. ... Material - nylon Nozzle - 0.4mm Layer...
thingiverse
This is a power plug mount for a DRZ400. I'm not sure which years it fits, although I'm fairly certain it will fit any model DRZ that has the same speedometer shown in the photos. It would be best to print with a more UV/temp stable filament. ...
thingiverse
Use this to organize your valvetrain components when rebuilding a DRZ400, it may also fit other bikes. I am almost complete with this it requires a few minor changes (see picture). I am uploading with the hopes someone can change it for me...
thingiverse
Carb Flange for the Amazon 39FCR Carburetor for the Suzuki DRZ400. This is the joint between the carb body and the airbox, it protects the rear air jets from unfiltered air. It funnels filtered air from the airbox that some other solutions out there...
thingiverse
Air Filter Cage (Holder) for Suzuki DRZ400 motorcycle. You need a glue (cyanoacrylate?) for this thing. Print "Leg" part eight (8) times. ... "PREVIEW.stl" just for view.
thingiverse
This is a simple lip with a mesh screen to help clean up the Suzuki DRZ400 after the 3x3 airbox mod. Keep In mind the hole will need to be cut SLIGHTLY larger then the traditional 3" by 3" in order to compensate for the air restriction caused by the...
thingiverse
This is a speed pickup sensor mount for the front fork of a DRZ400. ... I only tested it on the bike I have, a 2002 DRZ-400 kick however I believe these forks are the same for S and E bikes up until current model year.
thingiverse
Carb Flange for the Amazon 39FCR Carburetor for the Suzuki DRZ400. This is the joint between the carb body and the airbox, it protects the rear air jets from unfiltered air. It funnels filtered air from the airbox that some other solutions out there...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1731842 Instructions Using the following options: tag_width = 60 text = ArlingCon 2015 text_z_height = 1 frame_thickness = 2 text_font = Fontdiner Swanky tag_z_height = 1 text_size = 5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_width = 8 font_thickness = 5 hole_radius = 3 message = ‹:)2015 font_size = 10 Font = write/Letters.dxf stick_thickness = 3 flat_bottom...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58259 Instructions Using the following options: letter_4_shift = 0 letter_2_shift = 0 word = 2015 letter_1_shift = 0 letter_3_shift = 0 hinge_diameter = 1.77
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=290279 Instructions Using the following options: use_base = Yes use_childrens_cut = Yes base_length = 30 border_thickness = 1 ring_width = 4 text = 2015 resolution = 100 base_width = 16...
thingiverse
Print the top near where the skate bearings mount with a modifier and 100% infill. The first balancing stand is actually untested, the 2nd balancing stand is tested, but if you push it the wrong way, without a lot of infill, it affects the reading.
thingiverse
A speedo mounting bracket for an Acewell speedo (may fit more than one)
thingiverse
This is a mount to replace the OEM shunt-type rectifier/regulator with a Shindengen SH775 series-type R/R. This mounting plate utilizes the chain roller mount and the overflow tank mounting point. This is not my idea, just a mount I created. The...
thingiverse
I wanted something better than blocks of wood to hold my engine up while I worked on it. This is what I wound up with. they're so high so you can put the crankshaft thru, install the flywheel, do all of that stuff and still flip the thing over...
thingiverse
This is a bracket I designed that allows you to bolt a sealed beam 4x6 LED headlight in place of the DRZ factory halogen headlight. ...
thingiverse
Live stream of me making it https://www.twitch.tv/videos/1267331856 Designed around a 11mm hole
prusaprinters
<p>This is something I threw together so I could use aftermarket turn signals in the stock DRZ front turn signal mounts. <br><a href="https://www.revzilla.com/motorcycle/lightech-led-turn-signal-type-7?sku_id=1301395">The specific signals I use...
thingiverse
This is a low profile dash for any model year DRZ400S/SM/E using the stock light cluster, ingnition switch and a Trail Tech vapor speedometer. This mod was specifically designed to be used with a KTM headlight assembly but will fit stock assemblies....
thingiverse
This mount holds a Trail Tech Vapor along with your ignition switch. ...Not tested