250 quadcopter 3d models
20261 3d models found related to 250 quadcopter.thingiverse
design of my latest 250 quadcopter. the camera side is decoupled from the motor side (to a certain degree), in order to reduce jelloing. this seems to be necessary on this wooden frame since the hobbyking baby beast brushless motors generate a lot of...
thingiverse
Remixed from Micro H-Quadcopter by ukarmy04 Increased arm length for standard 250mm improved motor fixings Improved center fixings added feet
thingiverse
Antenna mount for 250 quadcopter(ZMR250, QAV250, Nighthawk 250, etc.) Use urethane straight tube (size : 4x2 mm). camera cover was included too. ...two models are available (1.4mm , 1.9mm)
thingiverse
250 size quadcopter PM1806 2300KV ZTW 18A esc (installed inside arm) 5030 propellers CC3D controller OrangeRX DSM releiver I needed some sending and drilling holes to mount all pieces because , but with sandpaper and dremel all pieces fit. ...Print...
grabcad
This model is for a LHI/EMAX nighthawk 250 quadcopter frame. I traced out the frame bits and modeled them before I assembled the quadcopter in order to make a 3D model to tinker with. There are a number of models and assets in this assembly that I...
thingiverse
Capacitor holder designed for a 250 quadcopter. Holds a variety of difference capacitors to react to different voltage ripple frequencies. ...Digikey parts list for the capacitors is included in the images
thingiverse
Mini spider 250 quadcopter upgrade, for GoPro or Mobius cameras (use a ZMR250 mount). Recommended setup (DIY as you like): 3s setup, 12A ESC: 1806-2300kv motors, 6x20 (slow and efficient flight) - 5x45 (fast flight) propellers, 3s 2200mah 25c...
thingiverse
Updated the design of the stock emax nighthawk 250 pro quadcopter arms with a more sturdy build. I've eliminated as many of the styling cut outs as they induce weak points near the base of the arm. This thing was made with Tinkercad. ...Edit it...
thingiverse
Instructions H-250 Quadcopter Frame Consists of 4 arms - I use ZMR 1804-2400kv motors or similar and 5030 props - could possibly fit 6 inch props. A 3 part frame consisting held together by nylon hex stand off spacers from Ebay. The middle frame...
thingiverse
Design Intent 20MM spacer designed for the ZMR 250 quadcopter. The intent is to use this spacer between the 2 bottom plates and place electronics between the plates and forgo all standard standoffs and the top plate to create a slimmer and lighter...
thingiverse
... friend who lost his carbon fiber landing legs in a crash. ... They are designed for [this quad](http://www.hobbyking.com/hobbyking/store/__78142__DYS_250_Glass_Fiber_Folding_Quadcopter_With_Storage_Case_PNF_.html), or others with arms around 14mm wide.
thingiverse
The interlocking shroud design is safer to fly, easy to print and the 250 mm quad size works on most printers. If you are a STEM educator, Axiom would make a great project for your classroom. It teaches important concepts in physics, engineering, and...
thingiverse
Here's a simpler to print quadcopter keychain, no holes for motor mount makes the design take less time to slice and print, should be a fun gift for the FPV people!!! ...Enjoy!
grabcad
Check this reddit post for more information: http://www.reddit.com/r/Multicopter/comments/2m0433/i_recently_started_building_250_quad_racer_from/ Components used: DYS BE1806 black edition (they sell them on bangg**d for fair price) Turnigy Multistar...
thingiverse
Work in progress of a new quadcopter design. The purpose of it was to keep the pieces to a low count and to make a printable model we can use as a prototype for graphic plates. Nothing super innovative here, it's a pretty basic H copter, just the...
thingiverse
Capacitor holder designed for a 250 quadcopter. Holds a variety of difference capacitors to react to different voltage ripple frequencies. Digikey parts list for the capacitors is included in the images. ...Version 2 adds some chamfers and extra slots...
thingiverse
This is a surround designed to fit the stand-offs on my ZMR 250 Quadcopter frame in order to protect the electronics housed inside. There is an aperture for the USB on the one side, as well as a lower opening for the Matek PDB that extends out the...
thingiverse
Unfinished 250 Quadcopter design, designed with OpenSCAD, with good math behind it so you can change a lot simply by modifying the variables at the top. It is still a work in progress, v13, the first (and at time of writing only) version I printed...
thingiverse
Something I threw together for a co-workers Quadcopter. ...It replaces the aluminum post in between the carbon fibre plates.
thingiverse
Brought to you by http://RCNewz.com This is a light pod that can be used on the front or rear of the ZMR250 and QAV250 quadcopters. ...It is designed to be used with two 5mm LED lights and is installed with a single screw.
thingiverse
Search Ebay for "Emax Quadcopter hardware" kits for a screw set. ... Chassis 2.1mm thick Arm 4.2mm thick, fits 6" props Top 1.7mm thick Instructions Emax hardware includes: 5 M3x6mm nylon screws 13...
thingiverse
The design is closely based on the original EMAX 250, and with a solid resin print, it weighs only 14 grams versus the 10 grams for the original carbon fiber. This arm does not require the use of a spacer :D I left a handy access area where the arm...
thingiverse
A 250-size quadcopter designed for learning to fly line of sight acro and perform tricks like flips and rolls. Specific design & build features include: - Robust 5mm top and bottom plates, with extra reinforcement on the base. - Arms also...
thingiverse
This is a 250 class quadcopter drone that is printed in a single part with no frame assembly required. I designed and built it as part of a course project. https://youtu.be/1B6fZqDwLBE Print Settings Notes: This was printed...
thingiverse
Requires moray's 7.3mm frame spacers from here (framespacer v3.stl): http://www.rcgroups.com/forums/showpost.php?p=29918506&postcount=215 These are used with Turnigy LED strips (7.3mm tall), and perfectly fit 6 LED's, with wires soldered behind.
thingiverse
30° FPV Cam support for Dialtone 250 quadcopter Frame
thingiverse
Some cosmetic parts and LED mounts for the ZMR 250 frame
thingiverse
Emax 250 mini quad feet and landing skid. ... ABS with 100% infill.