filawinder 3d models

I Reverse enfineered this in Fusion 360 to accompany a M6 bolt as that is all that I had

Simple brackets I made to mount my filawinder to the wall since my boards had no built in mounting points. Enjoy! This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3CoovCCiVf5

The pins on the filawinder's controller board kept grinding into my spools. I dimensioned the part and redesigned it in CREO but it will hold the spool farther out away from the control board. ... Haven't printed yet, but bearing may not fit based on...

Thus I have just added more flexibility to the Filawinder project made by Ian J.. Who is to credit for the hard work making it in the first place. Instructions I tried to make it more flexible. My...

This is a DIY friendly version of IanJohnson's electronics for the FilaWinder.

This accessory substitutes the PTFE tube to keep the filament inside the laser range of the Filawinder sensor holder.

Base on the Filabot Filament Gauge I designed this one for the Filawinder it works great for me i hope you like it as well.

Its based on the original Filawinder file The cylindrical section has also been shortened because its no longer necessary to squeeze the spool onto it. ...Also check that the arm doesn't rip of components from the board the spacing of the motor and...

If you're a Filawinder user, maybe you've experimented that if the produced filament, isn't perfectly straight, when it goes through the PTFE tube, probably it will drag the tube toward the spool, risking to break the servo. In fact the tube...

Filawinder/Filastruder was working great, but I had the nut back off a few times, causing a failure and top ramen. This nut holder just prevents the nut from backing off. This design is quicker than putting on a locknut. ...Simple and works well.

This is a modification to Ian Johnson's filawinder using printed supports, because I don't have access to a laser cutter yet. The motor support differs slightly from the picture posted. ... It has ribs on each side to stiffen it, and is 2mm thicker.

The FilaWinder comes with spool hubs that allow spools with center opening holes of a max of 55mm. You can use the standard hubs on holes up to 59mm but the spool then catches on the drive gear and control board pins so not ideal. Print 2 of...

... filament flow. Laser mount extended for bigger filament shadow. Extended filament guide that mounds on a servo. This filament guide uses 3.0 PTFE tube supplied with filawinder and is positioned into slot where you feel its most appropriate.

With my new Filastruder and filawinder in hand I have quickly filled the couple of empty plastic spools I've been saving, I also wanted some smaller spools for 250G runs of filament for some custom colours. I designed these to be simple to make with...

I found that really securing the tube so the tube doesn't move when the filawinder turns on/off, really helps consistency. (thus the white piece.) Original files included. I had to play with the 5 mm post diameters quite a bit to get them to fit. The...

If you are using the Filastruder + FilaWinder combo and extruding 3mm filament, then you will quickly realize how difficult it is for the servo motor (which controls the filament guide) to guide the filament from the left of the spool to the right,...

Intended for use with [Filawinder improved wall mounted sensor](https://www.thingiverse.com/thing:4199247) With gratitude to Greg Gaub for helping to test and improve this design. Please note that some components are designed with sacrificial...

I use those to hold spools attached to the filawinder.

A replacement for the stock filawinder laser sensor holder.  Fully parametric and customizable! ... I made mine a little wider than the standard, it works better with my white 1.75mm ABS filament.Print with support for the laser cutout!

Removed the little circle in the middle.

This a simple modification to the [FilaWinder Control Box](https://www.thingiverse.com/thing:174383) to be able to print it without the need for support. It uses 45 degree over hangs and a couterbore M3 cutout. ...Please use a hobby knife to cut up the...

I use Makerbot spools only and the stock gears on the filawinder are a little small for their spools, so I recreated both sets of gear and holders. This replaces the stock gear and holder STL's made specifically for the Makerbot spool reels. ... ...

I wanted to use the filawinder with larger spools. Actually, for 300mm Spools there is this modification: https://www.thingiverse.com/thing:1386376. But it doesn't contain a modification for wider spools. ...With this modified base you can use wider...

I mounted my FilaWinder vertically, and am using large spools (two normal 1kg spools with the ends cut off and glued together) so I needed an arm that was stronger than the stock piece, and could fit a slightly wider spool. This arm doubles the...

I needed my FilaWinder to go faster, but I didn't want to mess with the code or change the supply voltage to the motor, so I changed the gear ratio. The small gear is an 18 tooth gear, and the large gear is 38, so the ratio has gone from 13/43 to...

Filawinder extra support for motor arm. The new housing is brittle acrylic. This can help support the motor arm if you break the base. ...See my youtube video: https://www.youtube.com/watch?v=A7gB-qsbRRU

A replacement for the stock filawinder laser sensor holder. Fully parametric and customizable! I made mine a little wider than the standard, it works better with my white 1.75mm ABS filament. ... ...

I frequently see examples of users mounting their FilaStruders and FilaWinders on the wall, but I always see the sensor sitting on a shelf below them. I took h0lger's laser sensor holder, at its default parameters, and added 2 mounting posts on...

i checked before uploading this to see if there was another person who has made this there is but it has a scaling problem and like most people in this forum this person is so selfish that thinks there thing is perfect and will not even look into...

... that it is 90deg. to both guide and servo. calculate ratio of guide arm to to servo arm length, and that will be the number that you need to change in FilaWinder sketch/Firmware for guide movement correction. ... I hope someone finds it useful...