3 5in floppy disk 3d models

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   Among the first risen humans in Draksborne, Violet thought herself to be insane for her first life upon Tharador. For when she woke she remembered all that had...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size relevant to the...

The COMPLETE Dragonpeak Barbarians I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The people of Dragonpeaks are direct descendants of the Humans who lived in Aera under...

The idea is to loose both heat breaks, push both nozzles into the bed, then tighten the screws in both hotends to secure the heat breaks.CreditsCM3D MK3S: https://github.com/ComunidadMaker3D/CM3D-MK3SMK3...

The color thicknesses and the width of the outline stripes on this test print match the stripes on this case and future cases I upload will probably use similar...

For other projects and creations, please visit my Instagram page (https://www.instagram.com/roger.egli/) or check out my YouTube playlists for model/machining hobbies (https://www.youtube.com/user/MrZhefish/playlists). Hope you find this mod...

Larger or smaller screws can be used if you scale the model accordingly e.g. M3x8 screws at 150% part scale. Note: it's cheaper per screw if you buy in bulk from a specialist supplier. There are two versions of the container available, the standard...

Most issues with these printers can be traced back to this strain gauge probe not functioning properly.It would be convenient if their mainboards were compatible with the CR-touch / BL-touch probe style sensors found on the newest higher end Creality...

I considered adjusting the model but decided to leave it as is, as I'd rather have a more positive engagement that you can adjust to your liking than end up with one that doesn't latch in place securely enough. I'll leave this marked as a work in...

We successfully engineered an incredibly stable and secure mounting arrangement by adjusting the RC roof rack's structural reinforcement through computer-aided engineering models. By applying advanced design methodologies, our innovative product not...

We'll be using a simple character model for this exercise, so go ahead and import it into your scene. You can find the model in the "Models" folder of your project. Once you've imported the model, select it and go to Edit > Object > Group. Name the...

... you'd like to copy it into your workspace and mess with it. [Buy me a coffee :)](https://www.buymeacoffee.com/jcolega) - [Printables](https://www.printables.com/model/152611-lego-vehicle-wall-hangers) - [Thangs](https://social.thangs.com/m/65559)

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

This is a stepper motor-controlled model turntable designed for 009 but compatible with short N gauge locos (loose the fences). The bed is 100mm long, and the Arduino code will follow in the coming weeks. Primarily designed for DCC++ JMRI CMRI...

But 100% fan power isn't necessary, so use an lower Value and take the 100% as "headroom" for bridging etc.The bed leveling is done with an single DC42 IR Sensor (I can highly recommend them). Printing and InstallationAll parts can be printed...

[Large Sized Model - 25mm base] [Presupported in 32mm and 75mm scale]   One of the most respected Warbosses in the armies of Berogtor’s Yellow Orcs. Gazza was once a wonderer, living in the harsh arid land of the fallen Anshani Empire. He accrued a...

The hole for the cable tip should be wide enough for any similar cables, but if not you can pretty easily remix the model by just cutting the hole to be larger or adding material where needed. I suggest printing the dock upside down and including...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would definitely...

This is a multimaterial model. I don't have a multi material printer but learned that you can create a multi material print pretty easily without special hardware (as long as the multi material part does not span over to may layers - otherwise it...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: The Sightless Seer]   Born blind to noble parents, Irivyl was kept cloistered for many of her earliest days. When she drowned within the Prendael River as...

I have completed assembly and everything works so this addresses some of my main wants for this awesome model. I am also going to include the full parts kit here (the originals I used also), so everything you need is in this one thing saving any...

By the way, even though adding a vertical ring might seem counterintuitive, it does provide added stability while still maintaining the original model's benefits: no need for supports, and you can print directly without worrying about brim or...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the horizontality...

... screws. Now you can start the tank with the key and load it without opening it. PS: The original model has more than 200 rivets that the FDM Printer neither sliced nor printed. ...So if anyone wants a riveted version for a resin printer...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would...

This print allows to elegantly mount your Bosch eBike Charger to the wall, out of the way, right where you need it. I made this version because several people indicated that they liked my eBike Charging Station but preferred a standalone version of...

Then, once the mount is installed on the handle, you can unscrew the bolt and increase the distance from the magnit to the sensor, increasing it enough so that the brake sensor only activates when the brake is actually applied.The model is made in...

Print Settings: - Printer Brand: MakerBot - Printer Model: MakerBot Replicator 2X - Rafts: No - Supports: Yes Important Print Note: The key thing to keep in mind when printing these wheels is to use support material, especially for filling in the...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...