3 8mm 3d models
799973 3d models found related to 3 8mm.thingiverse
Scraw 3.8mm Print Settings Printer Brand: Up! ... Printer: Up Mini Rafts: No Supports: Yes Resolution: 0.2 Infill: 60 Notes: Scraw 3.8mm Post-Printing
thingiverse
Two part version of the 5mm wide simple cable combs for slimmer 3.8mm cables 8 wire comb, splits in lower and upper part
thingiverse
Clip on version of the 5mm wide simple cable combs for slimmer 3.8mm cables 8 wire comb, splits in lower and upper part
thingiverse
Tested on GBA Game Cartridge. ...Fits nice and tight. print this on a resin printer. I did 0.05mm height. Printed 3. The teeth can break. Print vertically or 20 degree angle. 3.8mm Security Bit and r 4.5mm Hex
thingiverse
gamebit for nintendo nes and nintendo 64 4.5 mm and 3.8mm. I have only made the 3.8 version and test it with success , when printing use the highest resolution possible. I uploded the 4.5 mm version but havent print it. If you print the designs...
prusaprinters
10 mm Slide-IN LED Strip mount for 2020 by Surrbradl08, thanks and 2020 LED Strip Clip by gaskins1992, thanks. I remixed to allow for an 8mm LED strip. ORIGINAL POST DATE 28-MAY-2019 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts:...
thingiverse
... thanks and <a href="https://www.thingiverse.com/thing:3623525">2020 LED Strip Clip</a> by <a href="https://www.thingiverse.com/gaskins1992">gaskins1992</a>, thanks. I remixed to allow for an 8mm LED strip. ... ORIGINAL POST DATE 28-MAY-2019
thingiverse
Screwdriver Handle for Electric Screwdriver Bits, 3.8mm with tabs. The bits does not go too deep into the back hole (Saperator Attached inside hole) Removable Bits or Permanently Attach with some Resin based glue. ... Made using another persons...
thingiverse
... with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44017 Instructions Using the following options: _6_cornerRounding = 75 _1_webbingWidth = 41 _3_edgeThickness = 2.8 _2_webbingGap = 4.4 _5_height = 2.8 _4_centerThickness = 4.4
thingiverse
Joins 3 pieces of 8mm dowel rod together either in a corner or T shape configuration. I am using it to create a cheapo weather proof shelter for my Ender 3 using dowel rod, bin bags and duct tape. ... Feel free to leave a tip if you feel it is useful...
thingiverse
Here 3 GPS Mount for a 8mm mast. If your 8mm hole is undersized/oversized when printed you will need to adjust your 'Hole Horizon Expansion' setting in CURA. That is a problem with your printer settings, not this STL file. If printed with a...
prusaprinters
I only have elastic that is 3-5mm so it wouldn't have worked great to try to wrap around the original Prusa US shield design (although I did remix a clip for that). So, I modified the design to accommodate an elastic (or otherwise) band up to 8mm...
thingiverse
Customized version of http://www.thingiverse.com/thing:43783 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=43783 Instructions Using the following options: height = 3.8
grabcad
nice and cheap solution for diy cable chains, my own design, and using it myself
thingiverse
After i had purchased my Borosilicate glass bed (220x280x3.8) I got annoted with using the bulldog clips so i made these instead.
thingiverse
Created this shim to raise the height zero location of the Z axis for easier leveling using a glass base plate (3.8mm). ...It mounts using existing hardware and swings out of of the way when not needed (as shown).
thingiverse
A simple 130mm rod with a ~3.8mm diameter. I made this to use instead of the metal rod on the Quick change toilet paper holder. ...http://www.thingiverse.com/thing:123068 Print Settings Printer: Freaks3D ...
thingiverse
I've switched to an 8mm sensor and came up with this design. I beefed up the sensor holder and added a recess for an m3 nut. I also added 1mm to the overall thickness and reduced the stiffening profile. ... Overall it's pretty rigid and works very...
thingiverse
Offset -40.1 , -3 Inductive probe sensor for Ender 3 Pro stock fan duct https://youtu.be/53FkIqdx8NU
thingiverse
Update 1: Added 5mm and 8mm feet These feet are made to rise the case from the surface with 3/5/8mm. In case there is a bottom mounted fan, this could increase airflow. ...
thingiverse
Customized version of http://www.thingiverse.com/thing:46095 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46095 Instructions Using the following options: x8angle =...
thingiverse
Customized version of http://www.thingiverse.com/thing:1808029 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1808029
cults3d
created this to fit my 8mm hotbed springs
thingiverse
created this to fit my 8mm hotbed springs
thingiverse
I have switched to an 8mm sensor and made some modifications to increase the rigidity. The clamp was beefed up and added a recess for an m3 nut. I also added 1mm to the thickness and reduced the stiffening profile. ... 12mm version is also included
thingiverse
This is the lead screw knob I'm using https://www.thingiverse.com/thing:3421795 Original Ender 3/2020 Extrusion Light Bar by LilTrublMakr https://www.thingiverse.com/thing:3272248 Original Ender 3 Pro Z axis stabilizer by Breinstorm...