3 axis controller board 3d models

This time, I'm assigning an optical x-axis end stop handle to you. Just like an optic sensor, I used a standard sensor (RepRap) from AliExpress - 3mm gap. Power the sensor with +5V; you can tap into it from the motherboard - just like in the picture...

Unsure if anyone else has this issue, but the left Z axis lead screw was rattling and had a lot of play for me, so this bracket stops that. To install you take the top cover off and undo the 2 screws holding the metal bracket to the case, then lift...

Mounting for the 40 mm stock extruder motor on the Y-axis. Offset from the original mount - 20mm. If you want to install the bearing on the second end of the motor shaft - the diameter of the hole in the mount is 24mm. I use small table...

it is in fact 12.12mm where it mounts to the upright, but 11.9 where to countersink heads are, meaning the flat surface where the motor mounts to is in fact at an 90.6 deg angle to the uprights, which is why the z axis bar is tight as it get down...

Adds ESD protection diodes to all signal lines, a local 3.3V regulator, bulk and bypass capacitance for the 5V and 3.3V rails, proper level conversion of SD card signals, and adds termination components to improve Signal Integrity. To install, plug...

The wire used for the control arms comes from marking flags at the dollar store, which are perfect for RC control arms and similar applications. To connect the servo ball joint, I glued six pieces of wire in place, cutting them to size as needed. I...

I'm adding a third Z-axis and seeking out an auto-leveling platform. Using Railcore's bed. I employed kinematic coupling to release stress on the parts. Need three Magball (https://www.duet3d.com/BallStudEnds) to keep things in place. And six...

None of the camera mounts seemd to fit the bill for me being able to have a consistent view of the print plane from the front, having something tied to the X-Axis and out of the way was the idea.This mounts a standard webcam looking from the back...

Optical Endpiece for Y-Axis. A high-quality optical sensor with inversion and a large (6mm) distance between emitter and receiver is available here: https://aliexpress.com/item/32728213054.html. Please note that you will need to remove one ear from...

Someone made a better version, get it here: https://www.thingiverse.com/thing:4968880 ------------------------------------- I couldn't find a cover for the backside of the Y-Axis of my Ender. There's a spinny wheel with a teethy belt around it, way...

Solidoodle's stepper motor for the X axis (NEMA14) is undersized, requiring over-driving and causing excessive heat, particularly in enclosures. To combat this, I tried using heat sinks, but they still didn't prevent motor overheating and skipped...

I'm using BMG clone extruder and the cable guide from llueen can't be fit directly - Z-axis brass nut blocking part of the guide. I have to remove some parts to get it fit. * llueen cable guide: https://www.thingiverse.com/thing:4723800 Also,...

I stiffened the Y-axis adjuster to make it more solid...it snapped twice during printing of really nice parts, and in both instances, it cracked right at the rear hook section...so I reinforced that area...and now it's functioning perfectly... will...

It's suggested to add a modifier to make the part around the holes solid, or after a while the PLA will sag & let go, and the bolts will loosen making the whole bed unstable on the Z axis as in : you'll be able to twist it and rotate it...

New version (V5) of my chain mount to NEMA stepper motor on Z axis. Printing: When printing this, the orientation on the printing bed is best with the chain side up and the cable hole at the top. The first versions were not strong enough with 20%...

New version (V5) of my chain mount to NEMA stepper motor on Z axis. Printing: When I print this, the orientation on the printing bed is best with the chain side facing up and the cable hole on top. The first versions weren't strong enough with 20%...

revised the Y axis adjuster a bit to be more sturdy... i had it break twice with really good prints...both broke in the same spot, right at the rear hook portion...so i beefed it up a bit... worked like a charm... will post a photo as soon as i...

A few different versions of the X-axis stepper motor bracket I have used to mount my BTT smart filament sensor and also have some clips to route the cables for the hotend. V1 is my original remix of some designs - the end stop switch mounts...

Cable Bracket Designed to Work Seamlessly with Teaching Tech's Rear Controller Box. Discover this ingenious cable bracket on Thingiverse, a platform where makers and DIY enthusiasts come together to share their creations. ...Visit...

Remixed to allow the bed on the Ener 3 v2 to have its full 235mm movement

I made the model to fit the ender 3 or pro.

This is a remix for the Ender 3 x-belt tensioner using native F688 bearings.

Qr code cover for the ender 3, print in a upright position for the best results

The slider and knob remain unchanged from the original anubis86 designs, which can be found here https://www.thingiverse.com/thing:3074280 along with the X axis tensioner. This design utilizes original mounting hardware and 1 M3x20 screw and 1 M3...

Replace your Ender 3's noisy board cooler with a silent 60mm fan for a smoother printing experience. This print has two parts, allowing you to attach the fan cover and prevent any debris from falling onto the board during assembly. Once printed,...

I replaced my Anet A8 mainboard with the BigTreeTech SKR v1.3 before converting to the AM8, so I designed a board mount based on pheneeny's concept. One version includes a mount for a mosfet expansion board and features holes that are approximately...

It utilizes RCTimer 2204 brushless gimbal motors for smooth operation and boasts 45 x 45 mounting holes compatible with gimbal controllers such as Storm32 and EVVGC. M3 screw holes are also incorporated for added stability, and the design is...

Made this because the x-cover from the ender 3 v2 is slightly different from the original ender 3. I personally like cows, that is why I put one on it. I also included a cover without anything. ...Enjoy!

There seems to be 3mm difference in the offset between the Z screw and the frame when comparing the Ender 3 Pro to the Ender 3 V2 Neo. ... Have remixed MammothMGs design to close that gap.

Ender 3 Lead Screw Stabilizer. ... I fixed it because it didn't fit on the 20x20 bare metal.