3 prong ac plug 3d models
799522 3d models found related to 3 prong ac plug.thingiverse
Added a ground prong to the safety cover, mostly to prevent any debris from entering a socket should it be on a workbench or table top.
prusaprinters
If I re-printed this, I'd probably go lower, like 25%? Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Yes Supports: Yes Resolution: 0.20mm Infill: 70% How I Designed This Modelled in Fusion 360 I designed this by first looking up the...
thingiverse
... are absolutely required. I needed to trim the model just a bit with an X-Acto knife where there were supports (at the bottom of the blades/prongs). One probably doesn't need 70% infill. ...If I re-printed this, I'd probably go lower, like 25%?
thingiverse
I wanted a cover for a three prong US plug, but I couldn't find one, so I designed this one.
thingiverse
Helps shield power plug ends from weathering. ...Modeled an extra for the cord of my engine block heater.
grabcad
Accurate scale. ... Male end of AC appliance plug end for power cord. Strain relief, stress relief. Three prong grounded plug with a short bit of wire. ...120V AC USA.
prusaprinters
STEP files and Fusion 360 .f3d file included so you can modify the clip if it doesn't fit your specific cable.I printed it with translucent PETG, at 0.2mm layer height, 3 perimeters, 15% gyroid infill. ...Any flexible material should do (PLA, TPU...
thingiverse
If the fit is too tight (either because of tolerances for the printer or the plugs themselves), then it shouldn't be too difficult to regenerate the design with slightly more generous tolerances. You want a snug press-fit here. This object was...
thingiverse
... charger plug when in your bag or suitcase to prevent damage to the charger plug or to other items in your bag. The 2-prong plug cover is designed to mate with an iPhone 5 watt charger, and the 3-prong cover will mate with any 3-prong AC USA plug.
grabcad
3 Prong Gripper Using stepper motor + worm shaft to create linear motion. Torsional springs are used on the last joint of each prong to ensure firmly grip. ...This gripper can be attached on UR10.
thingiverse
... thing. enjoy. 9/10---- This is just a 3 prong mount, i got tired of making them everytime and no one had them that i could find. so you can build whatever and when you want to add the mount just input it and add done. ...much faster and easier.
cults3d
The Center Prong is slightly longer to help dig just a little more of a trench. My 9-year old first saw this and thought it was a small back scratcher for him. I guess you could also use it for that, but it might not reach very far. I guess his...
thingiverse
The Center Prong is slightly longer to help dig just a little more of a trench. My 9-year old first saw this and thought it was a small back scratcher for him. I guess you could also use it for that, but it might not reach very far. I guess his...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_shoulder_th = 4.5 gopro_rod_nut_th = 3.6 gopro_captive_rod_id = 3.8 gopro_bar_screw_head_d = 6.2 gopro_primary = triple...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_id = 3.8 gopro_bar_rod_d = 31 gopro_rod_nut_od = 8.05 gopro_bar_screw_shoulder_th = 4.5 gopro_ext_len = 20.7 gopro_primary =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=46095 Instructions Using the following options: insideRadius = 2.5 y9angle = 0 z9angle = 0 y2angle = x4angle = 0 z5angle = 0 z2angle = 90 y5angle = 0 x7angle = 0 x5angle = 0 x1angle = 90 z3angle...
prusaprinters
This vase-mode friendly model prints quick and sits snuggly on US AC two prong cables.I print vase-mode with 0.2mm layer height, 0.8mm line width, and 3 layers on the bottom. ...Orient the face with the two prong holes but no gap on the bed plate for...
thingiverse
Had a cheap knockoff mounting kit that resulted in a same-same situation where both pieces were 2-prong. ...Needed a double-ended 3-prong adapter, so here we are.
thingiverse
AC Plug Cover by RebelTaz Somehow, I had this AC plug without the cover that goes with it. If you happen to have this particular plug and no cover... now you can print your own! ... Instead of printing at 100% infill, I find that using 1 wall (0.4mm...
cgtrader
AC power plugs and sockets connect electric equipment to the alternating current (AC) mains electricity power supply in buildings and at other sites. Electrical plugs and sockets differ from one another in voltage and current rating, shape, size, and...