3.5 hdd caddy 3d models

3.5'' HDD_NAS_Holder. ...The holder is composed from several 3D printed components, joined together with 3mm screws.

My specific use case is to add a 2nd HDD mount in the N-ATX v2 case which only has 1 3.5" HDD mount. One file has mount for a 60mm fan, the other does not. Unlike the above build, you cannot print 20 of these and continuously stack them, you would...

Foot for 3,5" external HDD AXAGON EE35-XA3 ALINE (https://www.alza.cz/axagon-ee35-xa3-aline-d1775025.htm). Compared to the original, it is easy to stick antivibration foam pads.Foots hold on HDD themselves, it is not necessary to glue them. ...You need...

3D printed 2,5" HDD (SSD) to the 3,5" HDD place in computer.

3D printed 2,5" HDD (SSD) to the 3,5" HDD place in computer.

hice una revisión del modelo: https://www.thingiverse.com/thing:4441076, lo afine un poco para que calcen los tornillos comunes de HDD 3.5", le adose un soporte para que queden con pies el rack y además lo hice para 6 discos. ...

print hdd stacking as mirror

Then I realized I would have a couple 3.5" HDD slots open so when I couldn't find a good 3.5" HDD storage box I decided to make my own. No supports needed. After you print both pieces, the hinge is sized so you can slide a 1.75 filament through to...

Hotswap 2.5" HDD/SSD caddy for old Fujitsu Primergy servers. Fits as a replacement for A3C40058356, see compatibility section for servers. Fits drives up to 12.5mm, however airflow might be an issue. You can use the metal piece from blank filler...

it's suitable for 20mm width HDD.

I tried using RetroGameRevival's file PS2_2.5inch_HDD_Caddy_GameStar_Full for my PS2 system (SCPH-39001) and it was 2mm too wide on the right and the HDD needed shifted left 1mm in order for everything to line up. Rather than trying to edit mesh's...

... ...It made sense then that I would utilize the couple of 3.5" HDD slots that were still available. When I couldn't find a suitable storage box for my hard drives, I decided to create one myself. No special supports are required to build this project.

A custom-built 3.5-inch caddy mimics the Dell PowerEdge (11th Gen) server's original design as closely as possible. Key features include drive ventilation holes, a designated spot to attach the drive's label, and two channels for Status and Activity...

This frame is for the original SCPH-10350/10281 IDE adaptors using the 3.5" IDE HDD. It was made to obstruct the airflow as little as possible, while providing a snug fit inside the expansion bay. It was made specifically for my SCPH-50004 (v9)...

Having 24.5 mm of length, a screw thread diameter of 3.5mm, and a head diameter of 8.5mm The wall must have at least 15.5 mm of width. If you use a longer screw, you must have a thicker wall. The project is designed to be printed with supports. ...You...

Credit for the original models: https://www.printables.com/model/40826-35-generic-hdd-caddy https://www.printables.com/en/model/383555-hdd-expandable-rack-v1 I made a NAS in an old PC case. Couldn't find the original HDD rack, I removed it years ago...

The caddy_side.STL file should be 3d printed twice, one for the left side and another for the right side.Can accomodate 10 HDD/SSD drives.Designed to be attached throught the bottom via 4x M3 bolts and nuts.

The caddy_side.STL file should be 3d printed twice, one for the left side and another for the right side. Can accomodate 10 HDD/SSD drives. ... Designed to be attached throught the bottom via 4x M3 bolts and nuts.

HDD Enclosure. No special setup needed. ...If you print with mesh down (see images) you dont need adhesion or supports.

This is a simple low-profile SSD / HDD caddy / tray for ThinkPad T430. Instead of the OEM bumpers with a pull tab, this one attaches to your disk with the standard M3x3 screws (qty. 4). It has two tabs that you can use to quickly pull the caddy out.

Four 3.5-inch hard drives are stored.

... material. The front panels can be either PLA or ABS. An allowance has been made for the 0.4 mm nozzle, but if a 0.3 mm nozzle is used, the front panels may need to be glued onto the caddy base. ...With a 0.5 mm nozzle, they might not slide smoothly.

Simple blank for filling HDD-Slots in Servers like Intel H2000 Series where slots are not allowed to be empty because of airflow.- v1: simple block with holes for screws- v2: cut-out where connectors would normally be

Stockable HDD enclosure. ...Suitable for 3,5" and 2,5" HDD in every height. ...

Stand for two 3.5 inch hard drives. For my home RAID system. ...Printed 4 at once.

Protective Sleeve for Hard Drive Disk 3.5" for storage and archiving. ...Printed with Dagoma DiscoEasy200 Etui de protection de stockage pour disque dur

I store my 3.5 inch backup drives safely inside this case, which also provides easy access to the SATA port when transferring data is necessary.

Stand upright for two 3.5-inch hard drives on a pedestal for my home RAID setup. ...I had four printed simultaneously to ensure durability and longevity.

Hotswap 2.5" HDD/SSD caddy for old Fujitsu Primergy servers.Fits as a replacement for A3C40058356, see compatibility section for servers.Fits drives up to 12.5mm, however airflow might be an issue.You can use the metal piece from blank filler...

The feet of the bracket is designed to fit securely into a specific part of the HDD, ensuring that the hard drive stays securely in place, even when under load. This design also helps to keep everything cool, as there is plenty of room between the...