3000 hd 3d models

3-part cover for Microsoft LIfeCam 3000 HD. The parts should all fit together printed as-is (i.e. tolerances are already accounted for), but I'm not sure if the fit on the cam is perfect as I made this for a friend, don't have the webcam. ... Assembly...

MICROSOFT USB CAMERA

A printable articulated support for lifecam.The pivot shaft is mounted with a 4mm screw (approx 5/32 in)

Holder to attach MS LifeCam 3000 HD to Y Carriage. 2 Versions available: rigid and compact. ... Design to fit 3mm carriage, but should work with bigger materials too.

... a mount for my HD-3000 webcam to use in my Ikea Lack enclosure. ... Found Siad:s " MS LiveCam HD-3000 mount" wich is great just that i needed a corner mount. ... To be used with cam mount and/or brace from https://www.thingiverse.com/thing:1707995.

This was a solution for mounting an HD 3000 Camera, an LED Cree LuxDrive wt Heatsink, and a Garmin Lidar Lite. Our objective was to place it as close as possible to a flywheel shooter without obstruction. Hope you find the concept modifiable for your...

LifeCam HD-3000 stand riser Note: scale it to 10%. ...

This is a simple wall or enclosure mount that will house a Microsoft HD 3000 Camera. ...It can be printed without supports.&nbsp;</p>

BOM: printed parts 1x M4x8mm screw 1x M4 profile nut 2x M3x30mm screws (DIN912) 2x M3 brass inserts 5mmx4mm (od x length) 1x small cable tie 1x HD-3000 cam (surprise, surprise) Print Settings Printer: selfmade Rafts: Doesn't Matter Supports: Doesn't...

This clip provides secure mounting for the LifeCam HD-3000 camera. You'll need to remove the floppy rubber-covered bracket by either opening up the camera and fiddling with impossibly tiny screws, or do like I did and cut the thing off with a...

Mounting bracket for Microsoft LifeCam HD 3000. Ideal for mounting camera under the top IKEA lack desk. For assembly one M2 x 20 Screw and one M2 Nut is needed. Print instructionsBottom part can be printed without support. Top Part was printed with...

Additional requirements: Microsoft Lifecam HD-3000 OctoPrint with a free USB port The original housing of the Lifecam HD-3000 will be removed and destroyed, the four screws will be re-used. Opening the original case (see picture): Unlock the two...

This clip provides secure mounting for the LifeCam HD-3000 camera. ...You'll need to remove the floppy rubber-covered bracket by either opening up the camera and fiddling with impossibly tiny screws, or do like I did and cut the thing off with a Dremel...

Some basic files to hard mount a Lifecam HD-3000 on your robot. Can be used for the camera alone, or add a high power LED on a heatsink. (Details still TBD, but see the notes section.) Also on Github: https://github.com/Techbrick/Electronics-CAD...

... 2020 extrusion. Add as many of the 2 arms as you need to get your desired position/angle. It's all held together by some M3x25 screws.&nbsp;Original mount: https://www.printables.com/model/266287-prusa-mini-webcam-bracket-microsoft-lifecam-hd-300

Support Webcam Microsoft HD-3000 pour CR10

Microsoft LifeCam HD-3000 Privacy cap

This is a simple but effective cover for microsoft's hd-3000 webcams. ...

Mount for the Microsoft Life Cam HD-3000 on the front 40x20 extrusion on the Tevo Black Widow. ... You will need: 4X M4x8 screws and slot nuts

Bed support for the camera Microsoft Lifecam HD-3000. It can be installed without any screw or clamp on the side of the hotbed. ... Tested on FlyingBear Ghost 5

These are vertical and horizontal go-pro mounts for cameras like the Microsoft HD 3000. If you want another mount just ask. ... I'm using this my bed mount timelapse with octoprint.

This is a Remix of this Guy´s hard work: https://www.thingiverse.com/thing:2647030 ! ...I used the arm of the Spoolholder and created a new Mounting for my Microsoft HD-3000 Webcam.

This disabled the video funktion by close the cam hole. ... I use it the most time as a microphone. Designed for Microsoft LifeCam HD-3000 ;) Rotate X --> 90° Thanks, Enjoy! ...

This is a very simple camera mount for Anet A8 and Microsoft Lifecam HD-3000. ...The mount features an adjustable slider for height of the camera and adjustable Yaw rotation of the camera.

Adjustable Height Base for MS Lifecam HD 3000 Print Settings Printer Brand: Printrbot Rafts: Doesn't Matter Supports: Doesn't Matter Notes: Print the pin slow!, I printed at 10 mm/s, the rest at 50 mm/s, print base with good fill % (around 80%)

Use three 1/4" bolts to secure a Microsoft Lifecam HD 3000 webcam into this cage. The tabs on the back are designed to work with my Linkos mounting system, which also uses 1/4" bolts. ...With this, you should be able to securely position this webcam in...

handy tripod support for MICROSOFT LIFECAM HD-3000 Better version remixed by dmarc73 herehttps://www.thingiverse.com/thing:2917065 Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: Yes Notes: the hole do not have the...

Simple bracket to attach Hd-3000 webcam to 6mm framed 3d printer (or, well, whatever you like that is 6mm thick really). ... I used the instructions here to open camera and replace stock bracket:...

Bed support for the camera Microsoft Lifecam HD-3000. It can be installed without any screw or clamp on the side of the hotbed. ... Tested on FlyingBear Ghost 5 **Please share Makes and feedback.** **If you liked it consider for a donation.**

Lens cover for Microsoft HD 3000 webcam. Enables you to block the lens in case you don't want to be filmed. The pictures show Version 1. I updated the STL-Files for better fit (microphone & status LED). This design features a two-lock system with a...