30mm fan guard 3d models
150629 3d models found related to 30mm fan guard.thingiverse
Fan guard/shroud that hopefully will make the fan blow less on the printed part.
cults3d
Fan guard/shroud that hopefully will make the fan blow less on the printed part.
thingiverse
guard for 30 mm fan ! ...you can choose between the square or the round one.
thingiverse
fits a 30mm fan The air is drawn in from the open underside of the jaw
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_holes_d = 5 solid_outer_border = 1 outer_roundness = 50 mesh_kind = hex fan_side_length = 30 mesh_offset = 68 mount_hole_width = 24...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_clearance = 1.5 solid_outer_border = 1 mesh_offset = 68 mesh_thickness = 1 mesh_holes_d = 5 mesh_kind = hex mount_hole_width = 24...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_density_ratio = 99 mesh_kind = radial_poly mount_hole_d = 3 mesh_thickness = 1 mount_hole_width = 24 mesh_clearance = 1 mesh_offset = 49...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_density_ratio = 100 mesh_offset = 68 mesh_kind = hex mount_hole_width = 24 outer_roundness = 50 fan_side_length = 30 mesh_thickness = 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mount_hole_width = 24 mesh_clearance = 1 mesh_thickness = 1 fan_side_length = 30 mesh_density_ratio = 90 mesh_holes_d = 4 mesh_kind = hex...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mount_hole_width = 24 mesh_clearance = 1 mesh_thickness = 1 mesh_density_ratio = 110 fan_side_length = 30 mesh_holes_d = 5 mesh_kind =...
prusaprinters
RPi logo added to the 30mm Fan Guard which was used when installing a 30mm fan for my new Raspberry Pi2 W for Prusa Link. Printed it in PETG with a color change out at the very end to give it a little color. ... Logo was taken from Thingiverse case...
thingiverse
This is a fan guard I threw together for my mp select mini. I decided to throw the Abstergo logo in there to give it some character. ...Print Settings Printer: Monoprice Select Miniq ...
pinshape
A fan guard (for the inlet side) with anti-backwash blades for 30mm fans. Helps prevent air spilling where it shouldn't. The small size makes it a bit fiddly to print, but even quite rough prints seem to work very effectively. I printed it with...
thingiverse
A fan guard (for the inlet side) with anti-backwash blades for 30mm fans. Helps prevent air spilling where it shouldn't. I use these for the fan on the extruder heat break with these fans...
thingiverse
Be that as it may (or "demo" in Japanese).I combined the two printer files into a sort of Attack on Titan fan guard. Haven't printed it out yet so please refrain from cussin' me out when it fails miserably. ...I don't even know if air will pass through...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_thickness = 1 mesh_density_ratio = 98 fan_side_length = 30 mesh_kind = hex outer_roundness = 50 mesh_holes_d = 5 mesh_clearance = 1...
thingiverse
Remake of this 30mm fan guard: http://www.thingiverse.com/thing:3202636 Trimmed this GPIO cover so it would fit covering only 34 pins: http://www.thingiverse.com/thing:1874648 The "Dual 25mm fans to 1 30mm or 40mm fan adapter" is here:...
thingiverse
... I wanted and dual color Punisher fan guard. ...The logo snaps on to the fan guard. It is for a 30mm fan but I suspect it should scale up 125% to 40mm just fine. I don't know if it will scale down though. ...The logo is already on the small side.
thingiverse
The Ubis 13 comes with a 30mm fan. This should help keep my fingers out of it. Remixed from: http://www.thingiverse.com/thing:445160 and http://customizer.makerbot.com/things/128718/files/261474 marked W.I.P. ...until I get one printed :)
thingiverse
Fan Grilles for 30 and 40mm fans. ...The 30mm grille is 1mm thick with a 1.5mm base and the 40mm is 1.5mm thick overall.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=128718 Instructions Using the following options: mesh_clearance = 1 solid_outer_border = 1 outer_roundness = 50 mesh_density_ratio = 98 mount_hole_width = 24 mount_hole_d = 3 fan_side_length =...
thingiverse
As it says on the tin... ...Post-Printing I hand-reamed out the holes with a 3mm drill bit to make fitting a little easier.
thingiverse
Customized version of https://www.thingiverse.com/thing:4837562 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4837562
pinshape
Summary Made a minimal fan guard for the 30mm fan on the Monoprice Select Mini roughly based on the printer's design language while still allowing maximum airflow. Print Settings Supports: No Resolution: .1 ...
thingiverse
Made a minimal fan guard for the 30mm fan on the Monoprice Select Mini roughly based on the printer's design language while still allowing maximum airflow. Print Settings Supports: No ...
thingiverse
After ruining two fans with my screwdriver I did this simple grille. I made it specifically very thin to not impact the airflow. ...Feel free to grab SCAD and update the grille as you like.
thingiverse
Just a fan guard for the 30mm extruder fan on the Monoprice Select Mini. This is the first model I've ever made and printed, hope you enjoy! ... -- Will S.
thingiverse
... But another day a little string of nylon filament blocked the fan and I immediately had to stop all to not overheating the hot end sink. Time to design this little boy. Only 1mm height! Installed 3 months ago and never an issue again with the fan.