30mm scope level 3d models
107423 3d models found related to 30mm scope level.cults3d
30mm level for hunting scope, requires 2 off M3 x 12 cap screw and nuts, 1 off 9.5 x 25mm spirits level
thingiverse
For 30mm scope tubes. ...Required hardware: 1 m3x16mm 1 m3x25mm 2 * m3 nut 1 bubble level 22mm L x 8mm D (commonly found in Harbor Freight type levels) Print Settings Printer: ANET-A8 Rafts: Doesn't Matter Supports: Yes Resolution: .3mm Infill: 90%...
thingiverse
Level for rifle scope for 30mm tube as well as a 1" tube Both models use Two: m4x14 screws Two: 4x4x6 heat insert One: 1"x3/8" bubble level
thingiverse
Añadido nivel de burbuja superior Requiere: 1 m3x16mm 1 m3x25mm 2 * m3 tuerca Nivel burbuja superior 10mm x 6mm ---...
thingiverse
Fixed all the flaws, slightly reduced the fastenings for the bar.
thingiverse
A quick and handy adapter to use your 30mm scope accessories on your 25mm scope. ... Shown in the picture is a 30mm bubble level mounted on my 25mm scope. ... PRINT TWO copies, one set for each side - place the larger side on the bed.
thingiverse
This thing is used to place you tiny red dot sight on you 30mm optical scope
thingiverse
Yes, there are many scope risers on this site, and here is my addition to the list. ...Raises your scope 30mm, and has a sight channel on the top rail. ...Will need (2x) M3x30mm screws and nuts to attach.
prusaprinters
I've created this to mount both my lpvo scope and my reddot to my airsoft. It should work with scopes that have a 30mm tube. M5 Screws are used to screw both halves together.
thingiverse
Needed a picatinny rail for my IR flashlight, so I made one! ... I have not been able to test if it can take the recoil from a 308, but it will work for Airsoftgun etc. It's made for 30mm scopes., Print with suports
prusaprinters
This is a elevation scope magnifier for a 30mm scope. Magnifies the numbers on the elevation turret by 3x for easier reading. </p><p>Assembly: Cut the credit card magnifier to fit the frame. ... Place magnification piece into...
thingiverse
PLA, PETG, ABS, ASA This is replaces the top mount on a standard 30mm scope. IMPORTANT - Print vertically stood up with the widest part as the base. 0.16mm, 40% Gyroid, 4 walls. Attaches using the same screws you would have after removing...
thingiverse
Bubble level holder and pointer for 30mm scope tube, m3 allen hex screws and nut.
thingiverse
i just designed this for my new scope i have yet to print it or test it. ...So if you do post your pics and let me know how it worked out for you...
thingiverse
Third test for these scope rings, attempting to hold a red dot optic in place on a Crossman F4 Nitro Piston Pellet Gun. -expanded inner hold -merged outer and inner bases -shortened height -other minor cosmetics Testing at 80% infill at .2 ...
thingiverse
So I picked up a red-dot scope at a garage sale really cheap, and thought it would look cool on one of my son's nerf guns, but none of the mounts I could find looked like they would work. I thought it would be a good idea to make the clamp part 29mm...
thingiverse
Scope Bubble level for 1inch or 30mm diameter tubes Hardware: Bubble Level: 9.5mmx25mm https://www.amazon.com/SODIAL-Acrylic-Bubble-Spirit-Diameter/dp/B0774MWSCS/ref=sr_1_15?ie=UTF8&qid=1547568605&sr=8-15&keywords=bubble+level+tube (1) small zip tie
thingiverse
Remix of 30mm Rifle Scope Bubble Level by ejulrich https://www.thingiverse.com/thing:2055428 Not much going on here. I just modified a 30mm ring to make it fit a 34mm scope tube. I like this type of scope level, as it is pretty tough, easy to see,...
cults3d
34mm level for hunting scope, requires 2 off M3 x 12 cap screw and nuts, 1 off 9.5 x 25mm spirits level
cults3d
25.4mm level for hunting scope, requires 2 off M3 x 12 cap screw and nuts, 1 off 9.5 x 25mm spirits level
thingiverse
This is a scope level. It shouldn't work but it does. Attach the device to your scope with a rubber band. Make sure the long part is referencing on the barrel. Turn your scope power to its lower setting. You shouldn't be able to see the reticle but...
thingiverse
... started with a center ID from the 34mm tube and then built from there to be able to add hardware for securing the pieces together. ...using a 10x10x29mm bubble level, i was able to snap it all together and fasten down with McmasterCarr hardware easily
thingiverse
Remix for a larger bubble. ... For 30mm scope tubes. ... Required hardware: 1 m3x16mm 1 m3x25mm 2 * m3 nut 1 bubble level 35mm L x 8mm
thingiverse
No supports. ...0.1mm layer height. No bed adhesion. Made for the monstrum lpvo mount and adapted to fit 1" scopes into it.
thingiverse
###File Info Nerf_30mm_scope_half_bolt_tighter.stl Half of the scope ring that takes the bolt. 0.75mm removed to make a tighter fit possible. Nerf_30mm_scope_half_nut_tighter.stl Half of the scope ring that takes the nut. 0.75mm removed to make a...
grabcad
Sample of a high-profile rifle-scope mounting with ring diameter of 30mm.Using M3 hexagonal socket bolt locking (not included on the model).Solidworks 2014
cults3d
V2 of my 30mm Scope Mount Uses common M4 and M3 screws. Objective is ~1.4 inches high for a medium height mount. No MOA accounted for in the base. Photos are from PRE-sanding and painting. If you print it, please post photos! ...If you enjoy this...
thingiverse
... rail but slides from the end so if both ends of the rail are blocked this part won't fit. This is in order to reduce the part count to two and should work with most airsoft guns PARTS LIST: 2x M3 10mm ( or 12 mm) screws 1x M5 30mm screw 1x M5 Nut
thingiverse
V2 of my 30mm Scope Mount Uses common M4 and M3 screws. Objective is ~1.4 inches high for a medium height mount. No MOA accounted for in the base. Photos are from PRE-sanding and painting. If you print it, please post photos! If you enjoy this model,...