ram with cooler 3d models
2771445 3d models found related to ram with cooler.thingiverse
RAM Cooler for 3 40mm fans. Fits perfectly on top of G.Skill Trident Z ram. ...Fans can be secured using M3 screws.
thingiverse
This heatsink was mounted on an asus z270f motherboard with ram corsair vengeance lpx. You need M3 screws and nuts and a maximum of 3 40mm fans. ...I'm not sure it fits other motherboards.
thingiverse
Used the Ram Cooler from Exioncore as basis and added two side skirts in TinkerCAD for stiffness. The RAM Cooler holds 3 40mm fans. Fits perfectly on top of G.Skill Trident Z ram. ... I used those fans...
cults3d
Just a ram cooler I designed for the corsair heatsink ram I am currently using, not sure if it will fit other models or not. Fans are 40mm Noctua attached using M3 hardware. Print with enough shells to allow the mounting holes to be tapped to accept...
thingiverse
Just a ram cooler I designed for the corsair heatsink ram I am currently using, not sure if it will fit other models or not. Fans are 40mm Noctua attached using M3 hardware. Print with enough shells to allow the mounting holes to be tapped to accept...
thingiverse
For anyone who wishes to remix my Ram Air Cooler for their own VR headset. On the output side of the duct, there is a cap on it which can be used to extrude outward from to cut a hole in whatever interface you wish to modify, then just slide the duct...
thingiverse
... variants. One with with a grate and one without to save filament. Print in PETG, PLA will probably soften. ... Brock123 original 120mm design https://www.thingiverse.com/thing:3505201 90mm fan base used https://www.thingiverse.com/thing:3685176
thingiverse
This was designed for patriot viper steel ddr4 and an x570 taichi motherboad so it may need modified to fit your components. ...Use 3mm hex head screws to attach the fan, or change the holes for case fan screws.
grabcad
A cover/cooler designed for SO-DIMM DDR4 ram. *SO-DIMM is for laptops, not desktops*Designed for mini-STX motherboards, can also be used with Asrock X299, C612, X99 ITX motherboards. (as shown in the renderings)-File: IGS, STP. SW2018, Keyshot-...
thingiverse
This is a RAM cooler that uses a standard 80mm fan instead of the usual pair of 40mm fans. The commercial coolers I've used have usually had two problems: - they had low-quality 40mm fans that started failing in well under a year. and, - they...
thingiverse
... just slide one side in and pull out the other side a bit and it pops in place. Designs covered by a Creative Commons Share-Alike License. You will need supports and i print it in ABS at .2 layer with 20% infill pc ram and help cool the ram off.
thingiverse
It is recommend to cover the inlet of the blowers with some tape or use the 7mm blower to CPAP adapter, if you can blink a lot I would recommend the 10mm. I'm working on a different version that will have adjustable airflow, just putting this here...
thingiverse
DDR5 RAM Cooler for DEEPCOOL REDHAT and GIGABYTE GAMING X. ... Helps to cool DDR5 memory by passing a part of air flow to memory.
thingiverse
I printed in white PLA, 0% infill with light supports, and painted with black acrylic. I'm also including the "peg hole" file in case anyone wants to put a hole in any other sets of horns/ears/etc. that are out there. ...You have to turn this into...
thingiverse
Tested with Noctua Fans and attached with M3 screws and nuts, but will work with M4 screws and nuts if your screw goes through the whole Fan. Ram used was Trident Z Neo. The only reason to have this mod is if you have a really high binned B-Die and...
cults3d
I combined the filament cooler with a clamp to attach the hotend wires to the cooler. The wires are also attachted to the bowden tube by clamps. ...You need the original hotend cooler https://www.thingiverse.com/thing:2751027 to mount all to the hotend.
thingiverse
I combined the filament cooler with a clamp to attach the hotend wires to the cooler. The wires are also attachted to the bowden tube by clamps. ...You need the original hotend cooler https://www.thingiverse.com/thing:2751027 to mount all to the hotend.
thingiverse
I made one cooler for my 50x50mm cooler, what is phasse forr all J head's
thingiverse
There is not a lot of space but you need to push the fan connector through the hole with all other cables and manage the cables nicely togheter. Put back the cover plate so all cables are back in place. 7. Guide the fan cable through the sleeve...
sketchfab
Pablo Picasso - Man with Ram sculpture 1943 Captured in Madrid at Reina Sofia Museum with Iphone X 160 images and processed with Metashape
thingiverse
just a hood scoop embedded in a ram charger hood. ...neither is my design, just my idea of the two merged
thingiverse
TRX4M with bumper. Looks pretty sick and does not really get in the way. Mounts on the original Bronco Chassis frame. ...No extra hardware
thingiverse
extruder cooler with 6x2 mm round magnets to attach the body to the extruder