30x30 vtx 3d models
7100 3d models found related to 30x30 vtx.thingiverse
... VTX03 and FRSky XM+ receiver. ... It can mount right in to a 30.5x30.5 stack. This design works with many VTX and RX combos so print one and see if it works for your hardware :-) This was originally designed for use on the RC Crazed Slimphast models.
thingiverse
Made for Reptile Dragon 1200 rc plane wing mount
thingiverse
Holds a VTX 30.5x30.5 size underneath an RC airplane with minimal drag and maximum cooling. Provides space for M3 locknut captured during install. ...Print in ASA for better temperature resistance as VTX can get really hot.
thingiverse
Just my design for mouting a TBS NANO VTX on a 30X30 mount. ... MUST PRINT IN TPU, the VTX gets Hot, pla will melt.
thingiverse
to adapt easily your VTX walksnail 25x25 to a 30x30 stack
thingiverse
Mount an AKK X2 Ultimate on a 30x30 stack, held down with zip ties. ...Bottom open for airflow
thingiverse
I've added another version to secure the SharkByte Vtx onto a custom top plate of the SouthEastFPV Leventador Sport racing frame so it is exposed to the airflow during flight. ... You can find the custom top plate for the Leventador here:...
thingiverse
I created a mount plate for placing my vtx and receiver on top of 30x30 stack. There are hole for fixing the component with zip ties, but i placed my with double sided strong duct tape. There is a small moldet socket for the antenna. I used a zip...
thingiverse
File Key: 3p13l = 3mm thick plate 13mm total height (original design) 3p12l = 3mm thick plate 12mm total height 3p11l = 3mm thick plate 11mm total height 2p12l = 2mm thick plate 12mm total height the naming convention follows the above trend files...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
cults3d
Didn't feel comfortable putting pressure on the VTX by placing it under the strap, so I designed this 30x30 stack mount. It still has plenty of air around it (vent strips on the bottom, side-entry, open top) - but I have yet to test it in the field...
thingiverse
Didn't feel comfortable putting pressure on the VTX by placing it under the strap, so I designed this 30x30 stack mount. It still has plenty of air around it (vent strips on the bottom, side-entry, open top) - but I have yet to test it in the...
thingiverse
This adapter requires no corner removal but is approximately 9.5mm tall which is about 3.5mm taller than the original to provide room for M3 nuts inserted in the corners after printing .Obviously bolts have to stop about 4mm in from bottom to avoid...
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
prusaprinters
a 30x30 mount for a matek F411-WSE flight controller, a M8Q-5883 gps module and a VTX-HV video transmitter.fits into the sonicmodell mini ar wing. heavily remixed from https://www.thingiverse.com/thing:4438702
thingiverse
This 3D Item can be use with any VTX that has 30x30 M3 screw holes and need to be held by 20x20 mounting spacing. ...This item was use on the ApexHD rear mounting space.
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
There is cut out for accessing the Rx bind button, However, seeing how almost everyone is using smart audio nowadays, I didn't bother, putting one for the VTX. But you're welcome to drill a hole in if you need it. Happy flying. Subscribe to my...
thingiverse
I created a Adapter to use the TX500 on a 30x30 Stack. ... Printed with PLA 100% Infill ,08 layer 40mm/s speed Inner Holes fit with M2 Screws (Attached at the TX500) Outer Holes fit with M3 (Standard size at 30x30 Stack)
thingiverse
This is a plate to mount in Armattan frame (is tested with Marmotte) some non stackable components with zip ties like (in my case) vtx, radio rx, buzzer with battery. The advantage is that the pad is linked tho the frame with bolts and nuts and...
thingiverse
it also has 20x30 gps m3 mounting points, VTX and ECS slots, the ESC uses 2 cable ties for be secured and the vtx is stuck down in the F405 and 30x30 versions and cable tied in the F722/F405 version. the F722/F405 are the same and are also the...
thingiverse
... a good place for the receiver. ... I figured mounting above or below would be too much heat, so I added a 90 degree receiver mount next to the VTX, on the same plane. ... I haven't tested it yet, but I like the protection, and there's a ziptie cutout.
thingiverse
Крепление видеопередатчика под стек 30 на 30
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: lug_length = 5.0 font_catch_diacritical_sign_strategy = bar and glyphs bar_vertical_shift = 5 frame_thickness = 4.5 frame_width = 0.0 text_color...
thingiverse
Needed some more space for a 30x30 vtx in my new TBS Source One V3 With this part I was able to mount another 30x30 stack in the back/rear section of the TBS Source One v3. I printed the part in TPU, the holes for the post are slightly smaller so...