37mm projectile 3d models
3562 3d models found related to 37mm projectile.thingiverse
37mm projectile for your launcher! ... -Print with the top open and fill with plaster for an inert round -Or print upside down with the bottom open and fill with smoke mix -1:24 RH twist rifled projectile -Optimized for vase mode printing, 45° degree...
thingiverse
I've created a couple of 37mm bofors projectiles. ...Haven't printed them yet successfully.
cults3d
This shell casing fits a 37mm M3 projectile. Roughly took shell dimensions off of a picture. Projectile fits tight, might want to bump up 1% or leave as is. ...230mm tall like original.
thingiverse
This shell casing fits a 37mm M3 projectile. Roughly took shell dimensions off of a picture. Projectile fits tight, might want to bump up 1% or leave as is. 230mm tall like original. ... <iframe width="560" height="315"...
thingiverse
There are all sorts of uses for this model from toys to rocketry to making 37mm projectiles. Enjoy and be safe however you choose to use them! The basic style fit flush with the outside of a 35mm film canister. The bushing style is meant to be...
thingiverse
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: facets...
grabcad
This is a 20mm M61 autocannon projectile. This model is based off of laser scan data of round. ...Reverse engineering done in geo design x.
sketchfab
A projectile model for a small game I worked on a while ago. This was the weapon used by the main character. ...It was modelled in Maya and textured in Photoshop.
thingiverse
This is a projectile launcher made for use in the demonstration of projectile motion calculations. It is adjustable from 5-65 degrees in increments of 3.75 degrees. Most rubber balls fit. The blueprints should provide any other information. You may...
thingiverse
A small hard projectile/bullet for a DIY 1/2" PVC Blowgun. Friction fit inside the pipe provides plenty of gusto when launched. The back/bottom have holes and a concave section for weight reduction and to make it appear more aerodynamic and sexy.
thingiverse
A solid taginn projectile that can be use to practice accurate firing of the taginn launcher. You will have to weigh an original taginn projectile and adjust infill density to match the same weight. I recommend increasing wall line count to 6-8 and...
myminifactory
This projectile points were used in throwing spears. They were launched by means of a device called Estólica where one part was used for the launch, while the other was ejected towards the target. They were used to hunt animals like guanacos. It...
thingiverse
Created 37mm standoffs/spacer to use with my MKS Monster8 cooling fan (https://www.thingiverse.com/thing:5428059) and DIN mount (https://www.thingiverse.com/thing:5428083). ... The hole is big enough to fit M3 screws.
prusaprinters
Created 37mm standoffs/spacer to use with my MKS Monster8 cooling fan (https://www.thingiverse.com/thing:5428059) and DIN mount (https://www.thingiverse.com/thing:5428083). The hole is big enough to fit M3 screws. Print Settings Printer: Tronxy X5SA...
thingiverse
This is a projectile designed to be used with a 37mm flare launcher. The body is printed in two parts so that the top can be filled with appropriate flare material before sealing the two haves together. ...The dimensions of the projectile are such that...
thingiverse
... just the projectile part of the round and not the case. The model has a height of 160mm and the bottom has a 37mm diameter. ...I printed this at .3 resolution for quicker speed, but .2 works as well This model was made using Fusion 360
thingiverse
... the round and not the case. The model has a height of 150mm and the bottom has a 37mm diameter. ...I printed this at .3 resolution for quicker speed, but .2 works as well Support material is not necessary This model was made using Fusion 360