3d event stage design

I used GIMP instead of Paint.net for drawing the topography; Octave instead of MATLAB for plotting the 3D model; MeshLab for simplifying the meshes, instead of Microsoft 3D Builder; Freecad2 instead of SolidWorks for the tunnel and the World Engine;...

Average those two altitudes, to get your result (we rotate and average to cancel out any errors due to the ring not hanging perfectly straight).Avoid windy days if you can't move out of the wind, as the ring blowing around reduces accuracy...

These tires fit on the Traxxas X-Maxx, which I think is an awesome RC truck:https://traxxas.com/products/landing/x-maxx/If you want tires that last a reasonable duration, here are links to Traxxas tires that will last far...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...

See the bundled "Using OpenSCAD customizer" PDF for more details.Recycling symbol offset: An extra thickening (positive offset) or thinning (negative offset) of all the symbol, to aid in 3D printing. Usually you won't need to add any value, unless...

Beim ChaosRun handelt es sich um ein kleines 3D gedrucktes LED Spiel für den kleinen oder großen Zeitvertreib und je nach Spiel für bis zu vier Spieler. Die Grundidee habe ich von hier übernommen: ...

They should work fine but I have not made a full clock with them, and they may get adjusted.This version has quite a few differences to the previous version:The face of the clock has been split into an outside ring (which holds the indicator design),...

They should work fine but I have not made a full clock with them, and they may get adjusted.This version has quite a few differences to the previous version:The face of the clock has been split into an outside ring (which holds the indicator design),...

the waterproof one is designed to use stainless steel plastic screws You will need 1 RCA to 2 wire vga balun (well technically 2, since you'll want one on the other end as well) You can optionally just fill that hole in instead if you don't wish to...

It is build to match the wled Board from Serg74, but you can use other controllers, too. The case has the following features:The "Stick" is rotatable 355° without the need to rotate the case itself.The rotation has snap points to reach exact...

A garden tower balance itself with the vases spread around to distribute the weight.Designed for plants that enjoy a define wet and dry cycle. Also easy to water, the excess water of one plant cascade down to the next and keeps dripping...

... so. After a spell card has been used, place it in a discard pile designated to the side of the deck. ...Discarded cards may not be used again (except with the use of special abilities like the 'Grand Grimoire' ability possessed by the Archmage).

In the future, I might add inconspicuous visual markers to the gears for alignment. Setting the time(edit 3)I did not intentionally incorporate this into the design, but the frame is flimsy enough in one direction for the gears to slip if you...

- Replace the stock extruder mount by the filament sensor holder This work is based on the original Superfly extruder design by Mustcode https://www.thingiverse.com/thing:4841682...

Want to buy storage?You can tip me on Ko-fi if you like my designs.I don't have a shop, but you can order storages from PCBWay on my project page.What's next?No more boxes planned. For now...Special thanksMarch on the GameBoy Discord for feedback on...

The construction costs are about 300€ and the construction time is about one day. contact email address ownplant@gmail.com Print instructions1.) Print out all parts and insert all thread inserts 33x "M4 Thread insert" they are all the same 2.) Saw...

This piece is a straightforward, no-frills chair, designed for functionality and ease of use. It's perfect for those looking for a simple yet comfortable seating solution. Made with high-quality materials, this chair will provide you with years of...

The pod bay is designed to be assembled separately and then fitted inside the sphere. EVA Pod Model I used BouncyMonkey's EVA Pod Model in my build. However, his model was meant to printed much larger so some fine detail is lost in the...

I do not have a way to lift the rear of an XC90 however as I have not been able to design parts for that yet. Here are some examples of expected results: <b> Top hat spacers only; <b> Gain 1.75-2" of lift. Mine are 25mm, for example, the Cross...

I do not have a way to lift the rear of an XC90 however as I have not been able to design parts for that yet. Here are some examples of expected results:</p><p><i><strong>Top hat spacers only;</strong></i> Gain 1.75-2" of lift. Mine are 25mm, for...

Loading in the middle position of the handle (measured from the top of the handle) 240g - The throttle is designed for installation in the side panel of the simulator or you can print a plastic base for it, the throttle with two buttons, one of which...

And to remedy this, in designing this monstrosity I have sacrificed everything: simplicity, optimal print orientations, even common sense. Still in terms of nerf “shotguns” this cross between a magstrike and a folding chair has much to offer. This...

UPDATE: 20.04.2022adapterplate (new design) for model C&nbsp;Hello, we would like to introduce you to our stealthburner conversion mod.&nbsp;At this time it works only with the klipper Firmware.&nbsp;The use with “Marlin” is planned later and will be...

Simple bricks to play with or to integrate into other projects, designed to be easy to print, and easy to integrate in all other projects.Printing parameters:PLA//0.4 nozzle//0.2 layer height//0%infill//no support//brim All the parts in the files are...

The design of the MIK adapter plate does not allow this. <br>So I created a adapter plate that is MIK-compatible and at the same time allows Ortlieb bags to be attached.</p><p>If you are facing the same problem, then you have a solution here. <br>I...

  Zach Freedman's work is available on Thangs, and you can find examples of his Gridfinity designs here and here, which are available under his MIT license.  If you like this model, or want to learn more about Gridfinity, you can check out Zach...

This is a 100% original design by myself. I spent time learning Blender while making this. It's easier to learn a new application when you have a goal. I was using 123Design forever. This is a a BIG print. It is 18'' Tall, 15'' Wide and 6" Deep. ...

If you want to thanks or support:PayPal Yandex money Benefits: Allows you to reduce the length of retracts and K-factor in Linear Advance, significantly reducing printing time Improved material flow control results in improved printing quality of...

I have a Gotek drive and CF-IDE card reader for my Amiga 4000.As I already use the 5,25” bay for a CD-ROM drive, and one of the 3,5” bay’s for the original Floppy drive, I needed another solution.My A4000 has a standard height floppy drive, so there...

This will require some post processing by filling the gaps with wood filler or bondo or some other filler. There is ~0.1 to 0.2 mm tolerance in each part that slide into each other. Most of the body parts are designed to require minimal supports...