3d model of link

Also added v2 keyring. I printed at 0.12 and 0.2. I had some issues with depth of the three lines so I had to make it thicker than I wanted. This is based on an in-game item from Apex Legends created as "Fan Art", no infringement intended. ...Send me...

...I recommend using supports; if you have Simplify3D, use the Customize Support Structures menu to place them as shown in the included screenshots. Post-printing, your freshly printed fan duct will be visible, with supports in some areas of the piece.

Camera to mount under a microscope and visualize the images via html on a monitor. In addition to the printed pieces you need: 4 screws M2.5 x 25mm (or M3 if the Pi holes are enlarged) 2 x M2 x 1mm screws 1 screw M3 of plastic, metal type computer...

The Coupler will help you run a short length of PTFE tube from inside the filament compartment through to the exterior and aloo you to print 3rd party filaments on large spools without having to leave the compartment door open. Add your 4mm...

So, I decided to combine the benefits of both systems by designing an Allen key probe using standard Z endstops. This is a quick and easy print project that doesn't require supports. To set it up, you just need to create a longer cable (about 90cm)...

When the cap is all the way on, it should spin freely. UPDATE: 2018-10-14 ========== I redesigned the clips that hold the cap on the Hex Driver because sometimes the old clips were breaking off when installing the cap, and included the new FreeCAD...

I'm not going to tell you what you want to hear or feed you a line of nonsense just to make you feel better. If something needs to be said, I'll say it straight out. I'm Not Going to Be Your Personal Assistant. Newsflash: I'm not your personal...

Just make sure to align the front and back of the two big parts correctly, as they need to line up perfectly. Check out the pictures I included for more guidance. ... If you want to see how it's done in action, check out this YouTube video:...

To build a secure enclosure for your Ultimaker 2, craft a pair of adjustable hinges and a robust handle using 11x12 plexiglass to form a functional door. This custom hinge design enables the door to swing wide open against the printer exterior when...

Probably it'll end as organic waste, like most of it's predecessors. Let's be realistic.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Wanhao</p> <p class="detail-setting printer"><strong>Printer: </strong>...

Here is the rewritten text in American English without any foreign characters, active voice and following Flesch-Kincaid test with a score of 100%: Customized Version: http://www.thingiverse.com/thing:53235 Created with Customizer!:...

Print this modification with a high infill percentage of around 60-80%. It's recommended to use PETG or ABS for this part since it will be near the bed, but PLA can also work well with such a high infill setting. 2. Screws: - For M4 T-nuts: 8 in...

### 7" LCD Display (ELECROW) with RASPI 3 (B/B+) For my OCTOPRINT station I used a combination of several components: Unit Raspberry Pi 3 B+ Display ELECROW 7" LCD Display with Touch Screen RPD10246D Display Size: 7 Zoll Resolution: SVGA Wide...

It is designed to fit a square frame tube with an opening approx 15.6mm (square) and outside dimension of 17mm (square). I printed mine in PETG (due to it being outdoors) and used supports and a brim due to the small size. Gazebo-end-cap-longer.stl...

Customized version of http://www.thingiverse.com/thing:739573 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following settings: font_size is set to 12...

To make caliber changes easier on the LeeSixPack Pro, I designed a new case feeder that allows for easy swapping of the caliber-specific drop tube. The following small parts are still needed for assembly. 1x washer 4.3 x 9 mm (comes between...

This led me to design a disc that stores 5 micro SD cards and allows tracking of used ones by flipping them over when putting them back in place. The built-in indexing mechanism prevents accidental rotation, stopping at the opening over a card slot...

This is a remix of McPcholkin. All the credit goes to Him, please. Thank you so much for this. Two round neodymium magnets: 8mm x 8mm x 1mm are needed. Original: https://www.thingiverse.com/thing:3652881 I also added the 3mf file from PrusaSlicer...

The exhaust parts are meant to be hot-glued to the fuselage's outer surface in place of the foam board engine components, and they hold up much better. I've uploaded a few thrust angle wedges as well to give it some downward angle that seemed...

Epoxy "Heatbed Clip" to bottom of heat bed, clamping until dry. 6). Enjoy printing! The Story: After burning out original heatbed wiring, I replaced it with 10 gauge threaded wire, which was a bit excessive but satisfying. Unfortunately, such thick...

Parts needed; Silicone/Gasket Seal Lock-tite 6/32 nuts and bolts - 24, 1 1/2" - 14, 2" For install this mounts center of windshield so only cut plastic near windshield wipers. No metal cutting or body work needed. Relocate all stock vacuum lines as...

Customized version of http://www.thingiverse.com/thing:739573 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following settings: Bar length trim is set to 0. Font narrow width is set to...

The OPTO optical port reader is a device that enables communication between any type of electricity meter equipped with a port according to IEC 62056-21 (old IEC 1107) and a reading device equipped with an RS-232 or USB 2.0 port. Amir mobasher ...

There will also be a clip available to secure the top and bottom of the pipes to the perpendicular pipes at the bottom. Keep your eyes peeled for that in the future. Other designs are available and are listed below. This design was created in...

There will also be a clip available to secure the top and bottom of the pipes to the perpendicular pipes at the bottom. Keep your eyes peeled for that in the future. Other designs are available and are listed below. This design was created in...

So for 5 minutes I designed this one.\nThe details:\nIts rounded so your finger fits comfortably inside\nSeparation from bearing, so it clicks securely into place and stays straight in its position\nits diameter is designed to show a bit of the...

There will also be a clip available to secure the top and bottom of the pipes to the perpendicular pipes at the bottom. Keep your eyes peeled for that in the future. Other designs are available and are listed below. This design was created in...

There will also be a clip available to secure the top and bottom of the pipes to the perpendicular pipes at the bottom. Keep your eyes peeled for that in the future. Other designs are available and are listed below. This design was created in...

This is 80mm tall when put together, so add or subtract height as you need for yours.There are large and small for both the top part of the case and the GPU support.You will need to print the GPU_TOP twice for the large.There's also a tunnel built in...

Customized version of http://www.thingiverse.com/thing:813330 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: Length is set to 123.8 Height tolerance for 5 series is...