3d panda 3d models

NOTE: all models are at initial stage and not refined, nor optimized for printing, only a rough idea at the moment The unmanned colony builder/Mars MkI is a project that seeks to automate the construction of shelters and basic facilities that a...

Any sagging of overhangs that occur at the very top/front of the model can simply be trimmed or cleaned away after. The mount can be either just press fit (if tight enough) or glued in place into the holes on the back of the body. I recommend gluing...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

Anser from Niklas: Hi Bas, take a look at Stefan’s video about filament drying, I learned a lot: https://www.youtube.com/watch?v=eqQRN9TUw08 You do need an active dryer, not just desiccant, but your Esun dryer might work (don’t know the model). Were...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

  I've been using the one in the picture for a few weeks and apart from not looking as pretty with the cam open, there's absolutely no difference in performance.I think I have allowed enough room to print this model with a .6mm nozzle but if you are...

Enjoy :) Update 04-05-2021: Adding ender 6 models, upgrading all to V4.3 (slotted mount holes for 2mm height adjustability) and adding "fan duct up V2" which has integrated grill. It's more tricky to print because of the small features so i'll leave...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

While it worked okay for most things, there came a time when I was trying to print a model with steeply overhanging points and the stock cooling just wouldn't cut it. I designed this adapter to allow a standard 5015 radial fan (24 volt, 0.1 amp) to...

If you want to save time while testing, you can print the included **calibration test** instead of the full model, but that is optional. Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It...

the vanilla singleplate model), though the pulleys included here are a bit different from those. Re-cut bolt/nut holes in the idler pulley holder and thumb wheel to accept M5 hex bolts (because those are all I have with hex heads :-P ) Added an M5...

(Rotate these angles accordingly if you rotate the model.) This way, you will have two layers of crossing extrusions in the spine folds. This makes for much stronger, long-lasting book hinges.</p><p>For<strong> print-on-print</strong> technique (used...

The handle houses the controller with its user interface and no base unit is required.All that is missing to be the perfect soldering solution for workbench and mobile needs is a stand and a housing.Introducing TStationThe TStation is a case for the...

It has been almost three months in the making, and several bits are an additional 100–200 sketches beyond the base model, which means there is a ton of Mf-detail, I probably overdid it. My goal was to create something special for kitbashing,...

Being in the United States, getting replacement parts for British model locomotives can be challenging, un-environmental, or impossible. but I found that the Bachmann Percy chassis shares a similar wheelbase to the 0-4-0's, and the Bachmann Duck...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_shape = 3 custom_right_port_length = 30 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

this model the reason I like it better is because it locks into place then you just press the button and it works so nicer better than the others hear that you just hold it in with pressure. Arduino program settings this is all new to me I...

** FUSION360 and STEP Sources are included **** I have my printer into an enclosure and, to save the electronics from excessive heat, I've designed this model to enclose all the electronics at a singe location. These were my requirements: -...

Tree Supports and possibly Outer Brim required for some STLs NOTE: The STL Models may display some artifacts from revision builds, but will not appear in Print RECOMMEND: Allow pieces to cool to room temperature on printers Heatbed before removing to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

...The design is optimized for the given print orientation - no need to rotate the STL model.You will also need two of the strain relief clips, which I have provided as a separate project.Assembly6 pieces of M3 nuts have to be pressed into the plastic.

And for many builders I consider this simpler than going the path of printing Flex material.  Model DetailsPulley and Bearing Press ToolThere is not much to say. It shows the pulley with a bearing and heat-shrink tube on the outside. The third...

And yes, I'm already working on another version to fit the standard width tank; it shouldn't be too difficult to scale it down from the XL model. I've also come up with an alternative design - a curved blade that's just as effective but looks much...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 11 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 45 use_stencil = 0 stencil_size = 40 stencil_shape = 6 stencil_mirror = 0 custom_back_extra_port_x_size = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_bottom_fillet_resolution = 8...

Or you can print the one with a cool carry handle.For the SFX version, click this link.&nbsp;&nbsp;What you will find in this packet:&nbsp;Base that houses your PSUBackplate for your GPU/Mobo IOGPU Mounting BracketMobo Tray without carry handleMobo...