3d print database

Like my original version, this one is also designed to be printed easily without supports. However, I've found that a brim is necessary on my printer to prevent the small cable cap and wall between the cables and hotend from warping away from the...

I'm new to printing and was really struggling with the corners on this thing coming up a bit and this definitely fixed that issue. I'm convinced it's just because I don't know what I'm doing yet. Either way, I just remove them with a razor blade...

... amélioré : plus esthétique (et d’autres éditions spéciales;) ), système d’éclairage led, etc. Pour suivre ces améliorations, n’hésiter pas à vous abonner a ma page Thingiverse et Facebook : https://www.facebook.com/waikikiprod Bon print à tous !

The basic mount would be printed in PETG, the camera mounts in PLA. The whole thing is VERY stable. The angle adjustment is connected with an M4 screw with 2 washers. As long as you don't bump into anything, the camera should stay in place and...

This inner step, which is the distal 5 mm length of the pin, allows insertion of 1.75 mm printing filament, to lock the pin. The pin itself is split with a .75 mm horizontal slice, so the pin can expand when the filament is inserted. The...

***** Print Settings Layer Height 0.2 mm Infill Density 20% Generate Support - yes. Build Plate Adhesion Type: Brim ****** I controlled the LEDs using an ESP8266 chip and software obtained from: https://github.com/Aircoookie/WLED ***** If...

The one on the left in the picture above is not necessary, if you have already printed the original version is will still work fine. But the one on the right needed to be changed to clear to USB jumper/adapter/180 degree thing.  I chose to use the...

... albums of all time, and they ranked Hendrix as the greatest guitarist and the sixth greatest artist of all time. Thanks for checking in on us and for your ongoing support.CR8ED Out Of Hand Sculptor - Sandy Campbell3D Scanning and Printing - CR83D

You'll also need a 2, 3, and 4 mm drill bit to clean out the holes unless your printer prints perfect holes. Drill out the holes carefully; I used my fingers for the 2 mm holes on the case. Use the Bed Triangle part to mark the two holes to drill in...

I had to print that after a craftsman tried to shorten the doors length in a rather barbarian style. The door is 83 cm in width - armed with an Ender 3 this translates to 4 parts with 205mm length each, leaving 1 cm uncovered as the door is so...

I would not fly this rocket on an A motor for obvious reasons. I recommend the following print settings:Nose cone - 4 perimeters and 5% infill. Rockets are more stable in flight with more weight higher up. Tail assembly - 2 or 3 perimeters and 5%...

By printing and using these data, you assume sole responsibility for manufacture and/or use, whether lawful or not. For any respiratory protection needs, please use tested and approved equipment. Industrial Property The piece model references on...

Plus tiny stool.  - Cupboard with microscope top option All the parts are pre-supported for SLA resin printing! This set works together with the Medical Bay set (the table, drawer & cupboard top options are interchangeable - there is also some...

I printed this with pla on my prusa mini with supports on the build plate only, 40% infill, 4 perimeters. for the support settings i used: Z contact distance: 0.2mm pattern spacing: 3mm contact layers: 4 xy separation between an object and...

Gracias Material list:1 unit – DDB Extruder V2.11 unit – Motor Nema 17 25mm 1 unit- Hotend V660-70 mm -- PTFE Capricorn 1 unit – Thermistor ATC Semitec 104GT (I recommend changing the original) 1 unit – 40W Heater Cartridge 24V...

The case is designed to be printed with a layer height of 0.2 or 0.3mm. You can lower the height if you want more details which is recommended for the ARC reactor. Supports are needed on some parts.I used PLA on everything but the electrics carrier....

After you have created these images, you will be required to print them out in your 3-D printer. Use your manipulatives to assist you in discovering the volume formula for the cones you have created. (hint: The formula will remain the same for EVERY...

The front face of this version prints separately because of overhangs that would cause trouble otherwise. Four 2 mm holes help with alignment when gluing the front face to the main body. I designed this with IBM PC's in mind for MS DOS use just to...

For Hotend Fan Recommendations, the user can replace the original 30mm E3D fan with a 40x40x20 mm fan running at 7v instead of 12v to improve quality prints and reduce noise. By connecting the fan's negative to the 5v supply line from an ATX PSU and...

A massive project undertaken by my tabletop group to play BattleTech, which faced challenges with both printed maps and hex-sheet setups due to persistent forgetfulness of terrain and later issues with terrain pieces getting knocked around on the...

This set contains 5 heavily armoured Kingsguard Heavy Cavalry equipped with lances.  the Riders and Mounts are separate models for ease of printing and painting. Presupported files are included for each model in both STL format and LYS (Lychee...

... FRAME To protect your frame, most sharp metal edges have a plastic cover. Print RodEnd.stl to cover–up the sharp rod end. It's not in the photos, but you'll know where it goes. ###BIKE The bike in the model is a Banshee Prime V3. ...

Edit 1: Separated the crab from Kraken Guard shoulder 3 to make it a bit easier to print. You'll simply need to attach Clad in the strongest armor the Legion has to offer, Tide Lords act as the shock troops and personal guard of high ranking...

His robot arm uses three 28BYJ-48 steppers for the outmost joints: Please "like" this thing or post your make as a token of appreciation for my work. Find my other fischertechnik designs here. keywords: 28BYJ-48 28BYJ48 case enclosure...

The bucket of the catapult was created using a Dremel 3D20, printing it out of PLA. How I Designed This Design Overview The catapult was designed to come together like a puzzle and have connections that require no form of fastening. It can be...

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

... compared with the normal version (+/- 2.5h less), a perfect solution for those who want only the TS100. SMALLER_xxx.stl's are not compatible with non-smaller versions, print one or another but do not mix them Timelapse: https://youtu.be/p505Rq6WJHY

... initial model was created by TigerAce1945's sdkfz 222, with possible elements from M-Bergman's 1:200 and 1:100 series. The origin of the tires is unclear. Production has not yet commenced; I typically have my models printed commercially in resin.

If you want to support my work, you can contribute with me by donating to this PayPal account. Print SettingsRafts:NoSupports:YesResolution:0.3Infill:Doesn't matterNotes:If you set the wall width to one filament line (0.4~0.6mm) and the infill...

Otherwise you will be limited to using “dumb” USB-A to USB-C cables.Print Settings:* 0.2mm layer height recommended* Supports only holding up the top of the body, not needed elsewhere* Tree supports strongly recommended (see images)Assembly:Several...