3d print final fantasy

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

Since the housing is hollow when printed with infill, it might tend to swim. So I recommend to drill some small holes in the outer shell to use the infill space for ballast water... The shaft should be 10mm in diameter and ca. 80mm long and made...

I had already printed my design when i decided to do this. So this is a patch, that why the wiring is messy on the pictures, in the future i will post a cleaner version of the pcb with tracks instead of crappy wires...) Once my build finished, i...

This part is printed with support on the build plate obviously. In order to make it fit, you have to take the housing off of the USB hub (just slip a dull tool into the gap and pry, there's no glue or clips) and trim off the plastic at the end...

You only need to print two sets of screws. One for the north celestial leg and one for another leg. The screws have 80mm length and can level at ~50° incline, so a distance of ~40mm. In the middle of the inner screw is a marker that shows the...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

I am modifying the original glass print bed to a fine-machined aluminum cast plate. I purchased this here: and used kit 4 with GFK/FR4 plate 1 mm and flat clips. Here is a brief description of the process: 1. I removed the four adjustment wheels...

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

Except for the spacer ring, all parts are printed with ABS for stability and the possibility of stable gluing. The spacer ring is made of TPU. For adjusting the air gap between rotor and stator, the space rings are 1 or 2 mm high and can be...

Changes I made to existing models: * Removed cable tie bump things because they're unnecessary and just add to print time. * Added holes on the Raspberry Pi panel so you can zip-tie extra Z cables in a service loop. * Changed the PSU front panel to...

different size fillets/rounding) and the hot-glued from behind to hold it in, M3x8 screws to attach XT60 holder to Lower housing. There are 2 holes, sized to accept M3 screws, on the side of the Lower for attaching “accessories," This side should be...

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

updated keyboard support update 05-02-2021 ------------------------ -updated top case to avoid printing defects -improved clearance of top cover update 06-24-2021 ------------------------ -included gap in keyboard support for diskdrive ribbon...

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

The gray and orange caddy shown here was my prototype and a number of improvements have been made to the design since it was printed, mainly regarding the fit of the deck boxes, keys, etc. The largest dimension on this is 9.7", with the height...

PRINTING ----- Nothing needs supports. I use transparent PLA for everything. I would recommend using the same colour for all mounts, but you could also colour them to match the cap, or code them to the country they come from or something if you...

PLA in my opinion is not resistant enough (humidity, temperature etc.) The logo and the wings are colored in orange and silver. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 40% Filament: CPE...

Print this with PLA if you want it to be semi-food-safe. Who knows what nastiness the ABS would leech into the roots and your sprouts! In order for these to work properly, you have to put the riser slats perpendicular to the tray's slats. If you put...

Print for four wheels 40 [roller from ab86uk](https://www.thingiverse.com/thing:3118584) and my two wheel halves 4 times each (2 identical halves = 1 wheel) in STL orientation in 0.2 mm and with 25% infill. Support is only necessary for the recesses...

... Note that the edge and corner brackets extend 6mm past the edge of the P5 panels, so make your wood frame 12mm larger than your matrix in each direction. Note - the picture doesn't show all the brackets attached yet because I'm still printing them.

... why I think I have such poor colors and so much diffusion in my photos. Once the pinhole was made, I cut it and taped it to the backside of my printed adapter with duct tape that I then covered with electrical tape (to avoid internal reflections).

Assembling one digit requires meticulous attention to detail: Begin by printing the digits in size 140 x 75 mm in mirror image and glue them onto strong cardboard. Bend the tab wire according to the digit's shape on the outside, securing it through...

Place them in position at the Bottom print and ensure they are fully seated before beginning soldering. Once done, you can snip off the extending length of the pins. Depending on your printer's overhang capabilities, you may need supports for the...

Stick the long M4 bolts into the bed and under-bed with the new springs between the two, then slide on the printed brackets with your tube inside. Slide the thrust bearings onto the bolts, and screw on your knobs. The knob will set the upper thrust...

When printing this jig, the only supports needed are below the two alignment fingers. 1/2" PVC - Metric Drill Bit [1/2" PVC Drill Jig - 12mm Bit - 1" Spacing](https://www.thingiverse.com/thing:5137859) [1/2" PVC Drill Jig - 12mm Bit - 1.5"...

Wrong way to do this as i didn't remember that you can't print white.So i re sanded the face and sprayed all the Light color. The water slide decal paper worked fantastic, Apply decals and swipe with a wad of paper towel. The clear letters of the...

Since my first-generation 2/3 plane connectors broke due to FDM layer separation issues, all the connectors in this series are printed so all connectors extend out on one plane, meaning that FDM printers are more than capable of building these very...

PLEASE CHECK YOUR PCB SIZE BEFORE PRINTING! I MEASURED MY PCB WITH A DIGITAL CALIPER AND IT MEASURED 65mm X 39mm EXACTLY Note there are many versions that look similar but have key differences. Make sure you use the one that is exactly as shown,...

First, print the elements before covering them with foil. I used aluminum tape typically used for sealing air conditioning ductwork; you could also use a thin sheet of metal for the element. For either design, holes are included to enable multiple...

To taper this wing just print the airfoils smaller and smaller to give the taper. So to reduce chord to 50% is easy. When you resize in a slicer it will tell you the length of the chord. So you just need to reduce this by typing the new value into...