3d print kriss vector

Leave me a comment if anything needs to be modifiedI preferred to make this support in 2 pieces to be glued with 2 centering studs to avoid removing the tedious supports after printingMarch 11, 2022: Added removable "capuchon amovible V2" which...

This also makes it easier to verify that the Bowden tube is fully seated.\r\nAdded a through-hole version for the extruder, which can be used when the extruder fitting has been pushed out of your BMG and you have an M10x0.9 tap.\r\nIncreased nut...

  Assembly instructions: View the link below to download the assembly instructions (same instruction manual as the “Crawler 4320 DC Expedition Cab”) aheadrc.com/manual   A couple of versions are also included for printing optimisation: Cab Full...

## How to print Printing everything using the defaul fast profile in Luban seems to work fine and everything fits snuggly together. (tested with snapmaker provided white filament) ##updates Just replaced the cornerdoglarge and cornerdoglargehole...

Here's what you need: * Hemera with square Nuts inserted in all 4 Holes on the correct side * 4x M3x8mm for attaching the E3D Hemera to the Connector (don't use longer than 8mm screws!) * 2x M3x12mm for locking the two parts together (can be a bit...

Since probably 95% of the people using these printers do not print with ABS or ASA, this new design is meant to be a much simpler and more innovative approach, as well as having far superior part cooling capabilities.I added a small wire retaining...

Here is the interesting Part: ; The second zeroing speed when Z is zeroing, the speed is slower M8016 I4 ; ================================== ;;;;;;;;;;;;;;Number of leveling points, ;;;;;;;;;;;;;;;;;;;;;;;;;;The first three parameters are...

You need to print out the direct drive plate, as well as the spacer in PETG. You could probs use PLA of some kind, but I myself am a little concerned about the plate warping due to the heat produced by the stepper motor. I might try a carbon fibre...

PRINTING: Use PETG or ABS if possible, PLA will degrade outside after a year or two. Printed with a 0.6mm nozzle. 0.2mm layers. No supports needed. Make sure you do not have any underextrusions to keep the plastic solid and waterproof. In the...

The lever print a Bondtech version to get rid of the massive gap. V6 or V6 Volcano duct works with either - the lock requires the bowden version or a clone heatsink to thread into. A tube straight down with an adaptor also works, however less stable...

After this, and a number of previous upgrades (see my other posts) the print volume reached new maximum: X=192mm, Y=218mm, Z=194mm per nozzle. The distance between e3D nozzles is 23mm. I finally got rid of the original connector PCB that was always...

This is a light remix of the Hollow Clock 4 by Shiura Before all, many thanks to him for this amazing design Main modifications are: - use a M5STAMP C3 for controlling the stepper - as a consequence, the box has been modified to integrate it - time...

The modules start as "printer capsules" sent from earth, and they land in a pack before constructing/printing themselves from a cache of on-board materials. The "Printer Capsule" files show the concept. Each of the modules has 6 sides, with a...

The printed part (light yellow/cream) sits below the whole assembly, and its clamped together with the rest of parts using said bolts:The remaining bolts and washers are used to attach the printed part to the chassis.NOTE. The model used to attach...

If you have any issues with the cable dropping too low (onto the print surface) or running into other things mounted in your printer, my "Cable Dangler" design is a nice effective fix for that issue (and makes the printer look much more open than...

When I printed the holder for the nimble, I realized I'd need to mirror it or change the direction of the extruder so that I could have the Nimble on the right side facing forward. I've uploaded two versions of the same design - one with the extruder...

This is the latest (maybe final?) version of my printed desk fan project and it's the first one that is actually a practical fan. The fan uses a centrifugal compressor to generate airflow, driven by a brushless DC (BLDC) motor that is controlled...

* Supports: Yes (if using Cura we recommend using the [Tree supports](https://support.ultimaker.com/hc/en-us/articles/360012614559-Experimental-settings) option and adding a 'Brim' to help the Tree supports adhere to your print bed) * Rafts: Doesn't...

Settings I use for a Tattu 450 mah 2 cell lipo, where the tray just sits over the bolt heads: bolt_c_c = 43.5; //center-to-center distance between bolts bolt_shank_dia = 6; //shank diameter of bolt (where bolting battery tray to quad frame) - make...

** You can purchase this case printed from my store by clicking HERE **This is a case for a RAKwireless RAK 5005-O WisBlock base board, designed with the Meshtastic project (https://meshtastic.org) in mind. ...It will accommodate the RAK5005-O base...

Dos opciones: Left - PAra colocar el seguro del mailon a la izquierda Right - Para colocar el seguro del mailon a la derecha El diseño original tuvo 2 versiones La version 1.0 tenia esquinas y un error de 2 grados En la version 1.1 se corrigio el...

I wanted to use a saddlebag and without a protection the bags would just keep banging on the motor. But what I consider the most needed addition to the original project was a anti torsion bar. The number 1 frustration I had so far was correctly...

I may leave it as-is since it's a lot less “sharp” than I expected when it's all printed out, but I'll try to add a wrap of some sort to maybe balance that out. CutsAll of the pieces should fit onto a Prusa Mini/ Ender 2 because the largest part is...

combined files now (was separate front & console)PU-548 chassis , entity with axles and wheels (just for printing on SLA printer I guess)the ladder extensionwheels and matching pair of axles (front/rear).rare guest seen on Sandmann street cleaner,...

... Print Settings Supports: Yes Filament: GIANTARM PLA, Feet: TPU maybe? Notes: No supports unless the one on the coat youll see on the picture. Be sure to print the coat upside down. Category: Art

Print the newer iteration instead: https://www.thingiverse.com/thing:3024361 Rektify is a sophisticatedly designed full-auto foam dart blaster. It is compatible with 130 to 180 sized DC brushed motors (possibly only 130 as a pusher, though it may fit...

My recommended print settings include 4-5 outer perimeters and shells on all sides, as well as 15-25% infill. Filament was PLA. Special thanks to the zerspanungsbude.net community, a German-speaking forum that provided valuable assistance during...

This works with my Amscope microscope. Print instructionsPrint in PLA with 0.05mm layers aka Ultra Detail. The printer must be finely tuned because the threads have near zero tolerance. Screw the lens on two turns then back it off one turn, like a...

However, the vast majority of ripped files from MWO are not optimal for printing, and while many other modelers are content with stitching these files together to make something workable, I decided to take it a step further.   Instead of just giving...

... Summary The Mini P is intended to increase accessibility to filtration equipment associated with resin printing. This is accomplished by releasing files for non-commercial use (don't make and sell these) and providing a sourcing & build guide.