3d print negative mold

There is a bonus version for those who can print multi-material with a Zelda Triforce design. While the two hooks on the sides do a great job of keeping the handheld secure, the hooks on the bottom and top needed slight tweeks. The hook on the bottom...

**Gravitrax Ball wheel V2** - Difference in height 80mm - no support necessary - 3 pressure parts: wheel, gear, pillar - Printing time approx. 8 hours - it is required: (motor see links) 1 x M5 screw 50mm or threaded rod 1 x M5 washer 1 x M5...

Use in place of magnets and glue both sidesCast a line out with a topper connectedConnect the body, and weight if desiredWait for bite indicationHook fish then pull the bottom off to reduce weight on the line when reeling inReel in, repeat Printed...

Place them in position in the Bottom print and make sure they are fully seated before you begin soldering. Once done, you can snip off the extending length of the pins. Depending on your printer's overhang capabilities, you may need supports for the...

Wrong way to do this as i didn't remember that you can't print white.So i re sanded the face and sprayed all the Light color. The water slide decal paper worked fantastic, Apply decals and swipe with a wad of paper towel. The clear letters of the...

What I would also recommend would be a silicone bed leveling mod, this can't hurt and you can align the bed exactly.And why the whole thing, the fact is, at high pressure speeds it starts to vibrate the X-axis and you have the so-called ghosting,...

I was thinking of printing JT3D's Affordable Rock Tumbler but wanted a little more control so I decided to build one based on an Arduino. The main thing is the stepper motor and using its rpm and steps/revolution to get an approximation for how long...

The switches are activated by two tabs mounted under the bed with M3 screws, nuts and the printed M3 T-nut converters (T-Nut-M3.stl) The upper Z-Axis switch is clamped to the Z-Stepper motor RHS mounting posts. The lowers mount just clips on. Make...

The sensor is quite near the nozzle, but I've noticed no problems so far printing PLA at 220-230°C. You may need some spacers to reach the right probe distance in the z-axis. Carefully check if the sensor reacts before the nozzle hits the bed. The...

Post Processing: As I usually do with my prints, I remove the supports, then sand it down, after this I apply two coats of primer, sanding between coats. Once the model is smooth, I start painting the model using acrylic paints and DaVinci feather...

I designed and printed this handle to fit the motor connected 3 18650 batteries, push button, mounted all of that and got a nice small low rpm cordless drill. Low rpm drills are needed in many cases for example for drilling wood and plastic. If you...

After a restart, the MMU will be connected or disconnected.I had to replace the power wires from the 2 pole connector to the Einsy as they were too short for my box.The support of the two connectors is screwed to the frame in the 2 already existing...

I wanted to be able to pop this item on and off when needed so I didn't want to use hardware, I've created some spring clips on the parts - safe to say that despite my best efforts prints this small will always be fragile and these clips are no...

It is though that below the ice in the surface it is a liquid water ocean, and it was early speculated that this ocean could hold life, with the geotermal heating from the tidal interactions with Jupiter and the other Galilean Moons (Io, Ganymede and...

This lifts the cables to eliminates contact and flexure of the cables during printing and it eliminates/obviates the need for chainlike cable housing to hold the cables and distribute/minimize flexing and possible wire breakage. ...In return, your...

Failure to do this will likely result in decreased print quality. I tried several Z wobble upgrades but few fit right and the ones that are close don't secure the lead screw. I designed this based off of my Tronxy P802MA printer and I can guarantee...

So I can't really suggest someone to print this and build it, it will be hard. /thats why I'm not sharing .stl files you mght need to change somethings) You need to know some Python and Arduino code to figure it out and get it to run. If you don't...

Print a bunch of cleats and bollards, they are always good. If you do make this, please please post a make. I'm very keen to see other people getting some use out of these files! ... <iframe width="560" height="315"...

I Haven't printed it but I'm confident that it'll fit fine. Update 28/07/17: A gallery with larger photos: https://imgur.com/gallery/p00SB Original text: Whilst I don't have any personal interest in altering the grip for other versions of the...

Print your fang with clear PETG. Just do it. You can glue it to the structure using Cyanoacrylate. Yeah, I know PETG doesn't glue with CA, but the fang has been modified so that using enough glue, you will eventually stick it. I just tested...

The launcher handle and rack parts should be printed in PLA (it's stiffer than other filaments) and with at least 3 perimeters and at least 20% infill. None of the parts need supports.LaunchingFirst, roll the wing onto the rack of the U-shaped...

... right?) 10. Do the reverse of Step 1 & re-level bed. 11. Move z limit switch up a few mm's/until nozzle doesn't crash into bed when homing. 12. Print away! ... Video: https://youtu.be/IBlSbVZZRGk Any feedback, questions or comments are welcome!

With these horns, you will be able to make fine passes with the drill bit, so that you can cut a wood with fine drill bits or grind the copper of a printed circuit board. All this makes ScoposPlotter unique. Extensions for Inkscape v0.92 and grbl...

... in and out you can select the top_cover. -- save -> rendern -> STL export -> close - Repeat the steps, to create a new picture frame layer, to stack this. - print all generated stl files. ... - To attach the modules via 1,75mm Filament and glue.

Tevo Parts used: All extrusions 3 Nema 17 40mm motors GT2 Pulley and idler Flex coupling 6x Wheels Leadscrew MKS Base 1.4 board Things I had to add myself: 2nd leadscrew 2nd flex coupler Z pancake stepper 2 smaller wheels PSU (Got a laptop supply)...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable retainer...

It prints quickly, uses only about 1 gram of filament (0.33 metres of 1.75 mm filament), and is very easy to use.It clips onto the spool of any brand of filament, so it's a universal clip. It can clip onto 1.75 mm filament or 2.85 mm filament, so...

Let me know if this was a good enough job that you would be excited to see more from me, and feel free to send requests I highly doubt this would print well with any other printer than a resin printer. I do not have supported versions of the files,...

To build, just print two ears, then attach the 450mm lengths to the tabs on the ears with t-slot nuts. It should be pretty self explanatory. m3x5 screws should do the trick, but if your parts shrink too much a washer may be useful to ensure a tight...

... on the screen, buy the cars used, and the old farts - like you - buying these vehicles new, do not have foresight to add this option. Save yours and possibly someone else's life by adding this to your low-spec VW. Print is ASA , PETG or Nylon.