3d print nintendo switch shell

I had trouble printing the arcade top so reinforced the bridges and prints pretty well. Takes more time to print and uses more filament but is more structurally sound than the original. ...I printed with a .6 nozzle.

Printer: MonoPrice MP Select Mini 3D Printer Settings: -Fill Density: 15% -Layer Height: 0.2mm -Support: Not needed *Make sure that there is no extra material around the bottom edge of either channel (where the JoyCon's slide in) after printing, as...

This model prints more easily due to its larger contact area. ...To print, you'll require the following components: one JoyCon Strap Holder Middle and two JoyCon Strap Holder Side.

Simple stand to display and store 10 cartridges.Print in PLA etc, very easy print.Took 2:45hr on my Prusa Mini  @0.25mm layers 

It can hold up to 10 games. ... It require one m3 bolt and nut. Printed in PLA

Mwinzer borrowed the design and slapped a super smash logo on it, check out his page for the print details.

I decided to print the stand on its side, and I'd recommend using a brim when printing on glass beds if adhesion is an issue - there just isn't enough surface area to hold it down securely. ... It would be awesome to see some pictures of your prints!

Activate thin wall printing Printing takes 3 minutes. Please give me your feedback :) If you want to thank me buy me a small file :) [EN] Just put in back of your sick joystick Only 3 minute print. Be sure to activate thin wall. ... Thanks to give...

I lost a stupid button after i opened up the joycon to replace the broken joystick. ... Print with button top facing up at .05mm. ... fits pretty darn well

Print logo one color and body another to give your game collection the spice it needs. ...holds 12 games and takes up little room.</p>

I saw a few card holders out in the 3D world, but nothing that I really liked so I made this one to maximise the space a bit more, it holds 12 cards in total while still being low profile.

It actually works quite well :)\r\nMake sure to thoroughly clean up all the leftover material from the printing process.\r\nI drew inspiration from https://www.thingiverse.com/thing:2308249\r\n\r\nJuly 23, 2018 brought an updated version that can be...

... game case holder that is cheap and simple to print, it dose have some wiggle room (~1.3mm). ... I have only printed the 8 segment game holder, but the single one works the same, only problem is it could fall over easily so it good to use for a remix.

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

This jig is tiny and simple to print, using 32 gauge wire with a diameter of about 0.3mm. Pause printing at 1.5mm layer height and force some wire into the slot. I suggest applying superglue to the wire after printing is complete. The ends of the...

Printed at 0.1 mm resolution, however, I believe it would not compromise the integrity to print it at 0.15, 0.2 or higher resolutions. ...To ensure smooth operation of the trays, I scaled the case to 1.08; your tolerances may be more precise than mine,...

I've Got a Hunch About the Origins, I've Already Built a Model for This Scenario to Ensure it Can be Seamlessly Integrated but I Haven't Run the Print yet, Let's Connect if You Have Any Thoughts.

I simply merged the two sections into one seamless unit, making it easy for anyone to work with even the largest prints without having to worry about applying glue.

Remixed the two part mount from Maxx1985 (thank you very much) to a single part model. ...Like that, you wont need a rubberband. If you print it sideways, you wont need support.

Print Settings: Printer: Monoprice Maker Select Rafts: Yes Supports: No Resolution: 0.2mm Infill: 20% Post-Printing: You will need to cut off the overhang supports near the tops of the rails. ...After that, the Joycons should be able to slide right in.

... Super Mario pipe was also included for visual appeal, as there aren't many games currently featured. No special print settings are required; all parts can be printed without support. ... ### Revision May 4th, 2018: Added alignment tool version 3

Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 150 microns Infill: 15% Post-Printing Metal Rails Removal from Joy-Con Wrist Strap Remove three Phillips screws holding the metal rail in place. Be...

Spade - Infil to add weight, no supports Letters - Print flat, already scaled to fit nicely in the embossing Star - Infil to add weight. Full print with 4x4x4 walls/top/bottom and 38% infil came to about 48g in weight. Glue in lettering and...

... tool for positioning the letters. I also added a liitle Super Mario pipe just for a nice look while as there are not so many games in it at the moment ;).There are no special print settings required. ...All parts can be printed without support.

Remixed from the Legend of Zelda inspired model created by Jpoel Layer 0.2 settings are optimized for the best results A moderate infill percentage of 18-20% is recommended for strength and weight Print this design at 100% scale to utilize a standard...

... game slots so I created this version. ...It can hold 17. I printed on PETG. I have a creality printer and the tolerances are good. Printer Ender 5 plus high resolution, The copied project is here. ... https://www.thingiverse.com/thing:2389588

Here is a remix of the model designed by Halasox, check out the original here: https://www.thingiverse.com/thing:3246275 This model has been sliced into three pieces for faster printing and compatibility with smaller printers. ... Assembly requires glue...

Loved the original design but felt like it could be optimized to cut down on filament usage. ...The original version used around 120g of filament and this version uses roughly 80g of filament. Prints in place with the bottom on the build plate.

Inspired by Marks great design i remodeled the game holder to hold the games from behind so it will be invisible on the shelf. ...Also i reduces the size wich brought print time down dramatically and is more suitable for smaller printers.

... ... This organizer slides smoothly onto the back of the dock and securely holds a Joy-Con grip along with two straps or four straps. I printed this design at a 0.2mm layer height, which took exactly one hour and twelve minutes to complete.