3d print xbox controller stand

my controller holder for series x

To hold the original controller in place.

Simple cover for XboxOne Controller pads

... holder from Thingiverse, referenced as 2553522. ...This accessory is tailored for use in an Xbox Android streaming setup, where it plays a vital role in keeping the device securely in place and ensuring seamless operation during streaming sessions.

... to get a bit more accurate shape of the controller in order to make a snug fit for the holder. ... Just print it in whatever color you want using 0,28mm layer height, use 3,5mm screws for the wall mount, slide the holder in place and you are done.

I found it tighter than tight, couldn't remove my controller from the clip so I had to cut it in half. I also removed the holes on top. Print on the side with supports between the 2 top clips. 2 walls, 2 tops and 2 bottoms so it bends. ... Fits...

... height and 80% infill. To install the retainer, squeeze it oblong to fit over the controller knob before inserting the extension, then press it into the extension to lock it firmly in place. ...If you want a permanent fix, apply a dab of ABS glue.

... screws securely. For those printing at home, note that Slic3r and Pronterface on a MendelMax 1.5 printer yielded favorable results, utilizing .3mm layer height and .2 infill. ...With these settings, printing time came in at approximately 40 minutes.

... be paid on cults3D to support me and I'll add a STEP file for this models, but all paid model will have a link to a free version. Free: Xbox One Fat Stand (https://www.printables.com/model/218015-xbox-one-fat-stand) Cult3D Exclusive: STEP file.

... will be paid on cults3D to support me and I'll add a STEP file for this models, but all paid model will have a link to a free version. Free: Xbox One X Stand (https://www.printables.com/model/218008-xbox-one-x-stand) Cults3D Exclusive: STEP file.

I've tested this on a 360 with the pack I made but the same should apply to a XBone controller.Parts list-3D printed parts6 x brass thumb tacks (4 if you reuse)2 x M3 washers1 x TP4056 battery charger with protection (eBay)1 x 1117-3.3 voltage...

Please enjoy this Xbox Series S Stand. ... ***If you have any questions or special requests please message me directly*** ***If you 3D Print it, please post an image of it, thank you!***

... needed. Be cautious when attaching your print to the controller stick, as the rubber is soft and easily damaged. This happened to me with my first attempt, which was too small. ...The current design fits perfectly, but be careful not to damage it.

Controller joystick extensions provide users with an extra level of precision and control over their gaming experience by offering additional analog stick functionality.

Simple, and secure wall mount. ...The controller sits close to the wall

holds 2 controllers removed material from center of remix and added side supports to prevent flexing

I have devided the controller mount to avoid any scratch on it

Minimalist, elegant design, optimized for 3D printing See all our designs in our profile Thanks for your support ;) 3D files are included for free modification. ... COMMERCIAL USE PROHIBITED FOR PERSONAL USE ONLY

While testing the original file on my nephew's controller, I printed a small test piece to see if the buttons felt right. Results show it fits perfectly with no issues. Supports: For tree supports, use Cura's experimental feature. Make sure you...

Print Settings Rafts: No Supports: No Resolution: 0.2 mm Infill: 5% Notes: You might get away with printing your first layer a bit too thick. ...This would create a lip, making it stick nicely to your controller without needing any tacky tape at all -...

Initially, I relied on a fine-tip pencil to create an outline sketch of the controller back from memory, capturing its nuances in meticulous detail. ...Utilizing vernier calipers, I carefully measured critical dimensions and employed a protractor along...

Then while i was fitting the original file to my nephews controller i tested the little test print out to see if the buttons feel nicely and results are that it fits with no problem. Supports: For the supports I use the experimental feature in Cura...

Remix on Gourdinos design. ...Added a hole so it could be screwed in, made it wider so the controller is more table, and rounded out the edges to seat the controller a little better

Please Like and Follow me for design improvements. ... For access to the 3D Printing Knowledgebase with troubleshooting and design education, join our monthly Ko-fi membership. ...https://ko-fi.com/3dpkb/tiers

Each grip is then able to easily screw into the nut as per the user's needs.They are designed with a textured outer layer to increase grip for the user. Included are 2 styles of grip:The long grip extends the joystick upward allowing for a more...

... or stuff like that and then print two of them. ...The hook on the furniture is 18mm wide. Edit the stl in Blender if you need another size. Print Settings Printer: Print Rite DiY 3D Rafts: No Supports: No Resolution: 0.2 Category: Video Games

... mentioning that their holders tended to bow under load. ...To address this issue, I decided to reinforce my own holder with an additional support beam angled at 45 degrees, which effectively distributes the weight of the controller and prevents bowing.

Final parts slide into place as I carefully snap the controller together. The clips secure tightly into the back plate, and everything fits snugly as it should. ...Sorry for the delay - a glitchy scanner slowed me down.

Modified this from https://www.thingiverse.com/thing:2923135 to fit two controllers in one. ... This project was created using Tinkercad, and can be easily edited online at https://www.tinkercad.com/things/kg2PeOjGIpZ.

No need to search for the controller and clutter up desks, sofas, beds ...etc... ... Practical and useful, to try it is to adopt it and not to do without it anymore 😁