3d printed dwarf miniatures

The rods should be cut to length (about 86mm, give or take, size them up against the holder once it is printed). I'd recommend cutting them so that they have about 1mm to 2mm play side to side once installed; if cut too snugly they can extend past...

 The only repair is replacement of the hammer, as epoxies and glues will not hold.I printed this using Prusament PC Blend, as this hammer needs to withstand some serious punishment to actuate the gas valves without breaking.  The PC blend...

Since publishing the Filament Server System in 2013, I've sought a more efficient system requiring less printing, fewer loose parts, easier assembly, and simpler spool changeovers. When creating the pipe-based, wall-mounted Spool Storage Rack last...

Extra parts needed for this project are: 4x - 8x3mm Magnets (Two for each piece) I printed this with a .6mm Nozzle, at 30% infil. No supports. **Design Features** - This case is designed to be a bit oversized, as Kraken dice are just a bit...

You can get away with with printing them bigger, especially 2 4 6 and 7. If you like my work please consider supporting me on Patreon. Become a Patron! ... Tinkercad link: https://www.tinkercad.com/things/8S3oiDKDSwc Some of my other designs: ...

If the magnets or bearings are tight in the holes, it could crack the printed part. Just reprint one or half a percent larger. NOTES: (1) Sometimes you might find that the hole is not centered in the blade, which means the blade could be heavy...

I speak up now only for the next generation of silent sufferers, which from what I've witnessed from the inside is the 'True Normal'.) I kind of feel like printing mostly Sixteenth and Eighth notes and rests, to suggest high energy and rhythmic...

Hello.I need to “repair” my 1080Ti fans because they started to make some weird noises and low the rpms, temperatures go higer, and… why no temperature and noise reduction upgrade ?First I want say the photos are of the first functional prototype,...

In using the shroud while printing a model that takes up the entire bed, I found that the wires from the extruder need to be routed over the output end of the fan using wire ties, as shown in the new picture above. As I'm using a low-velocity fan,...

Important Update - 22-08-2016 Please refrain from printing this design version as it has been found to contain incorrect belt paths, not set up perpendicularly. Check out the discussion on RepRap forum at:...

If you want to print the most cannon as possible, choose the normal models.I made also a "flat arrakis" or "board" version using the entire topography.The file's names explained: name_1_x_10_y.stl is 1 : x* 10^y. So _1_6_10_7 is 1:600000000 or one in...

Both had errors that prevents them from printing properly. ... ________________________ <b>If you like my work please consider supporting me on Patreon.</b> <a href="https://www.patreon.com/bePatron?u=30583762"...

This was printed on a Flashforge Guider II with high-quality settings, so the tolerances are good, but I also allowed a 1/4mm tolerance between parts, and at this level of quality, it gave me a good fit. Painting it used acrylic spray, primed and...

Refer to the link below for more information and print file(STL). https://surplusperson.tistory.com/800 If you found my designs useful, please donate what you think it is worth to my paypal.me. Your donation will be useful for a new housing...

The kit will snap into place, and you can refer to the video for instructions on preparing the case for use after printing and how to install the board. * LidNoOLEDConnector.stl: A lid with only cutouts for the click sockets and grove connector *...

Print two of each part, cut two 3-inch pieces of copper pipe (cut extras for replacement when the anode disintegrates). Assemble as shown in pictures; hook up solar panel. Hose clamps connect panel to electrodes, keeping them from slipping out of...

I recommend using technical skills to assemble it, but don't worry if you're not a pro - it's still easy to print and assemble. You'll need some common 2.5mm screws, but make sure they're short enough or use small ones (5-7mm long). Alternatively,...

Hello everyone, I've successfully converted my MegaTronXY X1 into a CoreXY Printer with an impressive printing area of 400x450x370. After learning about the remarkable speed of CoreXY printers, I decided to give it a try and upgrade my machine. So, I...

Print Settings: Printer Brand: RepRap Printer: Prusa I3 Rafts: No Supports: No Resolution: 0.3mm Notes: Optimized for use with a 0.4mm nozzle. Hardware Required You'll need the following components: Scisky Brushed Flight Controller:...

Printing in vase mode on a delta printer is quite a nice thing to see. Unfortunately finding one that matched exactly what I needed was tedious. I therefore decided to learn openscad in order to build my own general customisable low-poly vase...

With the use of 7 magnets on each part (fixed body has 7, each changable nozzel also has 7).Press the magnets (neodymium rods 3mm diameter, 6mm length) into the tunnels.Depending on your printing tolerances, you might need to drill the holes a little...

Place them in position in the Bottom print and make sure they are fully seated before you begin soldering. Once done, you can snip off the extending length of the pins. Depending on your printer's overhang capabilities, you may need supports for the...

So here we are about three months later with something that, after quite a bit of brainstorming, parts printing, carbon cutouts, messes and success stories, looks ready to be shared with the community. And now, it's over? Well not...

:)Print with support. My support settings in Slic3r which worked great:</p><ul><li>Support on build plate only: yes</li></ul><p>XY separation between an object and its support: 3.5mm BOM:</p><p>LTC1871 step up converter (67mm*43mm) to create 24 V <a...

Notes: Parts to print: 2x middle, 2x center, 2x center (contains mega x) 4x side, 4x corner Start mounting the middle parts using the original short screws. Once they are fitted you can easily snap in the other parts. To use the corner drawer...

Print top.stl, middle.stl, bottom.stl, and 4 pin.stl. Refer to the exploded view and attach pins through precise holes in these parts for robust construction. There are some special steps you need to follow here: 1) You may find it useful to...

At present, I prefer printing clean colors over dealing with frequent nozzle clogs from the OEM hot end. The bracket mounts to the new hot end using four 3mm screws. I reused one of the OEM heat break fans for the new hot end. The new hot end and...

Print the required parts (some will need supports), glue the splash guard to the top of the airlift pump as pictured, cut the mesh to size and glue through it with the mesh retainer holding it in place on the holding basket's window (superglue was...

Thicker panels and prints good now in 1/25th scale *UPDATE: 10/09/21* Uploaded a revised truck bed, this time with wall supports, Rev B *UPDATE: 10/06/21* Revised the truck bed, made the walls a little thicker and smoother, Rev A for both Pro Street...

This is still a work in progress and I haven't printed every file yet. Scenario : The French are retreating and have blown the river bridge in the local town and are holding the far bank. The German commander has detached battlegroups to either...