3d printed fpv plane

I designed and printed this handle to fit the motor connected 3 18650 batteries, push button, mounted all of that and got a nice small low rpm cordless drill. Low rpm drills are needed in many cases for example for drilling wood and plastic. If you...

This transformation enables my DaVinci to print PLA at 80mm/s with impressive accuracy and minimal noise, eliminating the screeching sounds associated with fast movements. Travel speed has increased to 200mm/s. This mod necessitates that Repetier...

The issue was that after a few prints, I had created a really cool "Rock". I wanted to be able to share the wonders of this illusion with the world, so I needed a way to present it. Did you know that "Necessity is the mother of education"? Armed...

All necessary parts for a compact, three-dimensional printed mini tri copter modelled after RCExplorer V3 will need to be acquired. This endeavor relies heavily on David Windeståls impressive design and accomplishments. Those wishing to assist David...

Your slicer should be able to handle both. The other version is also marked as a source so maybe the original creator will implement these changes in the base version (you can tell this is a remix if you know where to look and he/she might be able to...

After a restart, the MMU will be connected or disconnected.I had to replace the power wires from the 2 pole connector to the Einsy as they were too short for my box.The support of the two connectors is screwed to the frame in the 2 already existing...

I'm using a supplied ABS part on my MK3 and a self-printed PETG version on my MK2.5. There's a 3mm clearance on either side of the heatblock, hopefully enough :-)\r\n\r\nThis thing replaces the stock E3Dv6 hotend on a stock Prusa MK2.5 or MK3 with...

These prints require very little support if oriented properly with the rectangular sides face down - but you'll need good bed leveling and a smooth bed to get a good outside surface. There is support necessary around the SD card slot and HDMI ports....

Here's how to assemble the drill: First, print all the necessary parts using a 30% honeycomb infill and supports only if needed. I recommend adding at least a 10mm brim to the body part. Next, get ready your metal parts and motor. You'll need to...

It's larger than Phoebe, but lighter. This is because of its high porosity, more than a half of its volume is vacuum. The proximity with <a href="https://www.thingiverse.com/thing:3501867">Titan</a> makes its rotation chaotic, which means that the...

The switches are activated by two tabs mounted under the bed with M3 screws, nuts and printed M3 T-nut converters (T-Nut-M3.stl). The upper Z-Axis switch is clamped to the Z-Stepper motor RHS mounting posts, while lower mounts simply clip on. Ensure...

I added a calibration spiral and scaled it for printing. Attention: my firmware has been modified for me; it is crucial to edit and define the printer options, DELTA_HEIGHT and DELTA_DIAGONAL_ROD. Note that the motor directions for my TMC2100...

*Printed and checked. Passes XYZ Calibration and Selftest.* **Credits:** --------------- 1) Inspired by the MGN12 Linear Rails designed by Stwebster (https://www.thingiverse.com/thing:3400952) 2) Y-Tensioner and Z-Motor_Mounts are modified...

Maximum temp limit should stay under 260C during any time print takes while using this setup but please take precaution before attempting operation near temperatures much higher. Instructions: Upgrade with modular thermistor installation...

The hole is now 2,5mm so smaller when printed. A 2,5mm drill will do fine as a hinge. or any rod that hase the same diameter. I wouldn't drill beyond 3mm. I will later add some electronics later that I use to calibrate the spectrometer. The...

Using the Arduino IDE, create a new sketch and upload the following code: #include #include // Define the temperature sensor pins const int tempPin = A1; // Define the WiFi shield pins const int SSID_PIN = 2; const int KEY_PIN = 3; void setup() {...

Note that tolerances were added where the original parts lacked them; these should print fine without scaling adjustments. You will need two Z Nut holders, which are included in the name as a reminder. A photo showing version 1 is provided, but note...

August 17, 2018 I added videos with Banebot wheels and improved stepper support: https://youtu.be/ayka_9WWK08 https://youtu.be/4J9OeD_G4EI https://youtu.be/0Lg4ioItwHg March 10, 2018 First garage tests: https://youtu.be/bwohv99UVjI...

With S3D I can change my temperatures when I print from the machine control window, so I can use different filament using the same gcode. The base mounts the vertical coin holder base. The CR2032 holder is common. The fit is not real tight and you...

... for the cost of a pair of 120mm silent computer fans, you can have a silent B1! Oh, and it is so quiet now. All you hear is the fans on the head and the steppers when they move at high speed. :)I printed this on a BIQU B1 using eSUN PLA+ filament.

Potential fixes might include: * a "print-in-place" design for the cap which includes a solid and captive axis pin, * replacing the M2 screw with a very small rivet (strong, but not desirable due to tooling requirements and permanence of...

The print should fit snugly between the power supply connector and the RF shielding. If you happen to have other jacks, just go ahead and check the OpenSCAD source how to modify it according to your needs. ... Finally: Have fun playing the old...

If you want to print the most cannon as possible, choose the normal models.I made also a "flat arrakis" or "board" version using the entire topography.The file's names explained: name_1_x_10_y.stl is 1 : x* 10^y. So _1_6_10_7 is 1:600000000 or one in...

Added calibration for cyclic, to counter for printing settings/assembly differences, that can lead to displacement of centers of axes. How to use UnoJoy software: 1. Upload the "simchair.ino" sketch to your Arduino with an Arduino IDE. 2. Install...

Therefore, when you choose a spring, its inner diameter should be approximately the same as the outer diameter of the tube.How to usehttps://youtu.be/2PpO4AbOWggThis welder is designed to join the last filament of a roll to a new roll.When using this...

Would you like to learn more about creating prints featuring OpenForge designs? Please refer to the License FAQ for further details. OpenForge has shifted towards patron support, with contributors utilizing their provided resources to develop higher...

This is a remix of the device at the following URL: https://www.thingiverse.com/thing:4341389#Print%20Settings This is significantly different on the outside versus the original model. I needed to change the shape so I could mount this directly on...

... were destroyed after the war to comply with the alliance treaty obligations. The end. Print Settings Printer Brand: Anycubic Printer: Photon Rafts: Yes Supports: Yes Resolution: 0.02 Infill: n/a Filament: anycubic resin green Category: Model Robots

Note: If you have Saint brakes, (or another Shimano 4-piston design) Mngnt has this version which works for four-piston Shimano brakes Print instructionsCategory: Sport & Outdoors Summary Shimano technical training has a process for cleaning the...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the left to hide the screw holes. If you want to...