3d printed hard drive enclosure
2496983 3d models found related to 3d printed hard drive enclosure.thingiverse
The hard drive is mounted to a 3D printed enclosure. The hard drive clock utilizes (1) Adafruit Metro Mini 328 Arduino compatible controller, (1) ChronoDot - Ultra-precise Real Time Clock, (1) NeoPixel Ring - 12 x WS2812 5050 RGB LED with Integrated...
cults3d
The hard drive is mounted to a 3D printed enclosure. The hard drive clock utilizes (1) Adafruit Metro Mini 328 Arduino compatible controller, (1) ChronoDot - Ultra-precise Real Time Clock, (1) NeoPixel Ring - 12 x WS2812 5050 RGB LED with...
thingiverse
The hard drive is mounted to a 3D printed enclosure. The hard drive clock utilizes (1) Adafruit Metro Mini 328 Arduino compatible controller, (1) ChronoDot - Ultra-precise Real Time Clock, (1) NeoPixel Ring - 12 x WS2812 5050 RGB LED with Integrated...
grabcad
WD Easystore 1 to 4 TB hard drive case/cover- 3D printed with the help of polyprinterand the material is Ninjaflex Lava, with no support and standard settings for printing.
thingiverse
... body and the box, you can print them upright. I used buildplate supports for the enclosure body, but honestly, my printer could have bridged just fine. This is gonna be the best hard drive enclosure you've ever seen, folks. ...Trust me on this.
thingiverse
This enclosure fits a laptop hard drive and leaves the SATA connector open so that you can plug in a USB to SATA adapter and use it as an external drive. Pay no attention to the terrible print quality in the picture. I got a bad spool of red...
prusaprinters
This enclosure fits a laptop hard drive and leaves the SATA connector open so that you can plug in a USB to SATA adapter and use it as an external drive. Pay no attention to the terrible print quality in the picture. I got a bad spool of red filament...
thingiverse
Hi makers Here is a 3D model to turn a computer hard drive into an external hard drive as well as the connector cover. All the screws used are m3 screws. Do not hesitate to heat the screws and nuts to get them into the print and have a good clean...
thingiverse
Hi makers Here is a 3D model to turn a computer hard drive into an external hard drive as well as the connector cover. All the screws used are m3 screws. Do not hesitate to heat the screws and nuts to get them into the print and have a good clean...
thingiverse
... drive. ... This enclosure fits a laptop hard drive and leaves the SATA connector open so that you can plug in a USB to SATA adapter and use it as an external drive. Print the top on its side with supports. Print the base upright with supports. ...
prusaprinters
This is similar to my other hard drive enclosure, but this one fits a 9.5mm drive. This enclosure fits a laptop hard drive and leaves the SATA connector open so that you can plug in a USB to SATA adapter and use it as an external drive. Print the top...
thingiverse
This model of the Hard Drive Enclosure series was designed with the idea of being more space and material(s) efficient. The model (both top and base) require only 32 grams of material to print with 100% infill. At a print height of .1mm, it'll take...
pinshape
This model of the Hard Drive Enclosure series was designed with the idea of being more space and material(s) efficient. The model (both top and base) require only 32 grams of material to print with 100% infill. At a print height of .1mm, it'll take...
thingiverse
A hard drive enclosure designed to be used with most 7 mm, 2.5" hard disk drives or solid states. Assembly will require two, 12 mm, brass standoffs and the corresponding M2.5 or M3 screws. I suggest the use of M2.5 as they were the only ones I...
thingiverse
... on eBay for 20$) and a 140mm fan in the back panel to cool the drives. ... To make the full assembly, you will need: 4x tray cage mirror -mid 4x tray cage -mid 16x drive tray At some point, I will make a spacer to allow the use of 2.5-inch drives. ...
thingiverse
A simple enclosure for a 2.5" laptop hard drive. Has a snap tight lid- no screws needed. ... Printed with PLA at 0.2 mm, 10% infill.
thingiverse
this enclosure will hold 6 3.5" Hard drives and 2 120mm fans. ... bottom is cutout to be stackable.
thingiverse
... Updated the file to include 0.125" of clearance around the hard drive. Going to add foam or some other material inside to keep it from moving and creating noise. *UPDATE 8/12/19* Reduced clearance to 0.063" (1/16") all around the hard drive.
thingiverse
I updated my laptop hard disk to a SSD and made this enclosure to use with a USB to SATA adaptor cable to enable me to continue to use the old disk as a portable drive.
thingiverse
Watch the process: https://youtu.be/bu5joiCwyyE I created a simple enclosure that works with 2.5" laptop hard drives and the Acorn SATA to USB cable. ... Simple, but does the job!
cults3d
I updated my laptop hard disk to a SSD and made this enclosure to use with a USB to SATA adaptor cable to enable me to continue to use the old disk as a portable drive.
thingiverse
This is a collection of modular units that I created to hold several handy Western Digital MyPassport external hard drives. I created the designs to handle the four drives I have connected to a little server. They were slipping all over the place. I...
thingiverse
... system. It is designed so you can turn it sideways and place two of them side-by-side no problem. Enjoy! Let me know if it works! http://www.bestbuy.com/site/insignia-3-5-serial-ata-hard-drive-enclosure/5824308.p?id=1219163971636&skuId=5824308
cgstudio
Hard drive made with Cinema 4D R14Price: $30.00 Date added: Oct 28, 2013Product id: 541daf2b1e43f6d40e4a4ded
cgtrader
A hard disk drive (HDD), hard disk, hard drive, or fixed disk is an electromechanical data storage device that stores and retrieves digital data using magnetic storage and one or more rigid rapidly rotating platters coated with magnetic material. ...
cults3d
It is a box for storing hard drives, specifically has 5 slots. Suitable for 2.5 and 3.5 inch HHD. 10% fillers No support required. ... Height 126 mm.
thingiverse
I purchased a number of WD Elements external 12TB hard drives, and pulled the drives out to use in a server. I was left with the USB control boards from those externals, and wanted to be able to use them. I created both an active and passively...
prusaprinters
This is my first project I made this case to protect my USB HD Printed in flash forge pro PLA everything snaps together print setting are included in print setting.png file highlighted in yellow printed on my ender 3v2 in about 4 hours fits 2.5inch...
prusaprinters
I purchased a number of WD Elements external 12TB hard drives, and pulled the drives out to use in a server. I was left with the USB control boards from those externals, and wanted to be able to use them. I created both an active and passively cooled...