3d printed hexacopter

(Which are based off of MikeyB's Quadcopter.) Changes from the previous design include: 2 more arms, for a total of 6 Longer arms, Better landing gears Overall redesigns for improved usability The hexacopter was printed on an UltiMax DYI 3D printer...

... angle for support at 87 deg. Arms needed to fit inside the body with a rubber hammer (press fit) and cover fitted better if it was printed at 105% scale Magnets used are 8mm diameter and 1mm height, ebay have several places to buy cheap magnets...

fits http://www.thingiverse.com/thing:159756/ hexacopter. ...only isolated a single leg, all credits to http://www.thingiverse.com/wtn

... anycubic i3 mega (30-60 % infill, support for bottom part) Ahoy!!! Check my others things and guides (how to) build fully printed hexacopter on: http://drone-core.com/others/gorhex ;) Gorilla 3D Printer: https://www.thingiverse.com/thing:4261903

http://www.thingiverse.com/thing:1299137 - Full 3D Print Y6 HexaCopter Flame V3) Some video:https://youtu.be/pb2V_UGtkoM Print Settings Rafts: Doesn't Matter Supports: No Resolution: layer 0.25mm Infill: 100% Notes: Parts x Number of print (Infill):...

Camera Mount for Full 3D Print Y6 HexaCopter Flame

LED mount for Full 3D Print Y6 HexaCopter Flame Flame:http://www.thingiverse.com/thing:1046175

As subject, GPS Mount for Full 3D Print Y6 HexaCopter Flame (v2) For Flames:http://www.thingiverse.com/thing:1046175http://www.thingiverse.com/thing:1001202

As subject, Gimbal Mount for Full 3D Print Y6 HexaCopter Flame (v2) Flame:http://www.thingiverse.com/thing:1046175http://www.thingiverse.com/thing:1001202

Anti Vibration Mount for Full 3D Print Y6 HexaCopter Flame Vibration in PIX/APM cause strange behavior for my Y6. So i design this anti- vibration to see if the problem can be fixed. ...Flame:http://www.thingiverse.com/thing:1046175

... ARM and MainFlame. ...Main Features: Full 3D print part. Foldable arms Version 1: http://www.thingiverse.com/thing:1001202 Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Notes: Just ARM request support. ...I use PLA with 0.25mm per layer

Main Features: Full 3D print part. ... Foldable arms RECOMMENDED CONFIGURATIONS: 6" ~ 7" propellers 2206 ~ 2208 1500kv motors 2200 ~ 2800 mAh 3S lipo battery Flight control not bigger than 50x50mm https://youtu.be/w6PvrBE9mSs Instructions Printed by...

Y6 Rack third generation New design ARM locker Because above point 1 improvements, wire can through inside the arms New 3DR Y6 style landing gear Merger battery panels & lower layers center plates Vibration damping motor mounts Foldable GPS holder...

Mount Feiyu Tech FY MiNi3D 3 Axis Gimbal to Full 3D Print Y6 HexaCopter Flame V3

A Collection of some Parts for a FULL 3D Printed Hexacopter. ... (some parts i made at myself, other parts are from somebody else) parts i DONT made: https://www.thingiverse.com/thing:556185 https://www.thingiverse.com/thing:432598 ...

Hey guys, here is the project i'm actually working on, it's an mutlicopter "kit" design to be easily made with a simple 3D printer (even though most of the frame parts can be laser cutted too) Just decide which kind of copter you want (hexa, quad)...

More info and pics at:http://blog.lowres.xyz/ Everything that can be 3d printed is 3d printed on the multi copter. (PLA). 710mm between motor centers 6x 800kv motors 2x 5000mha lipo batteries ~30minute flight time (23minute aggressive flying or 38...

Newer MK3 Version at https://www.thingiverse.com/thing:2895964 710mm Hexacopter (6 arms). More info and pics at:http://blog.lowres.xyz/ Everything that can be 3d printed is 3d printed on the multi copter. (PLA).<br/> 710mm between motor centers<br/>...

Enhanced ARM Flame:http://www.thingiverse.com/thing:1046175 Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.25 mm Infill: 100%

Flame:http://www.thingiverse.com/thing:1046175 https://youtu.be/zh8ArzIEKKg

This is enhanced ARM to make sure it is strong enough to handle 450 Y6 Flame Flame:http://www.thingiverse.com/thing:1046175

Original design is great, but my motor cables are too short. Also, it was really hard to fit plush ESC on such short space between cable openings. So I've moved top opening closer to the motor which fixed both of my problems. ...I am not sure yet if it...

Hexacopter Multicopter updated using NAVIO2 flight computer.

Hexacopter Multicopter updated using NAVIO2 flight computer. Category: R/C Vehicles

To mound round ws2812b x16 LED under the motors. ...Flame:http://www.thingiverse.com/thing:1299137 Example Movie:https://youtu.be/YKy_UaBvD-Uhttps://youtu.be/peAPkQYNOpI

Small conversion plate, to fit ardupilot controller on the top plate.

As we all know about the principle of 3D printing – or “additive manufacturing, AM, additive processes are used, in which successive layers of material are laid down under computer control.” (quoted from wikipedia) , so if the lower part is smaller...

First IterationInstructionsIt was inspired the RCexplorer tricopter, Flitetest anycopter, and the 3D Robotics Y6. The majoritgy of the parts are laser cut, but I ended up printing some 3cm and 1cm spacers where needed. ... More details (materials,...

Upgrade for my T-Hexa, landing gear for easy installation on frame. ...ready to print

Revised version of the original https://www.thingiverse.com/thing:1168629 Stronger Hub. Navio2 flight controller. Motor mounts now have a locking pin for positive location. FPV camera..... ... You will need Freecad to customise or generate STLs...