3d printed light shade

It is very easy to assemble and if you print an array of this devices you can have a grid for domestic use or outdoors activity like in a camping etc. This wind turbine device is a part of a further open turbo-machine system based in a pending...

Use one stepper for Z ## Proposed solution: Print: * 1x back_nut_mount * 3x KP08_608_Mount I spent around 30 minutes assembling it and another 30 to level my bed (hopefully the last time). ### Shopping list: 1. ~1200mm GT2 belt loop 2. ~100-600 GT2...

Hardware needed: 18x M3x8 (or longer) bolts 18x M3 nut 1x M8 threaded rod for spools (length 172mm when fixed midway of box height) 2x M8 nuts and some washers as spacers between spools 2x Pneumatic air quick release fitting with 6mm diameter thread...

Do not glue the skewers into the holes; even if the printed part literally just falls off the skewer, winding the thread onto it will keep it all securely together. ...Not gluing the skewers in will also let you remove the skein label and reuse the...

... the 2 pole connector to the Einsy as they were too short for my box. The support of the two connectors is screwed to the frame in the 2 already existing holes. I printed everything with 0.2mm ABS. ...Filling 30% - 5 + 5 layers - 3 perimeters.

Note that some of the parts need to have the orientation changed in order to print. Feb 7, 2021 I updated the mount block to cover the wires and prevent them from being damaged. I will soon have the case for the TTGO/Display ready. It uses a...

8x2,6mm (2 for the bottom 2 for the top)FilamentFor me Bambu Lab or Prusament filament is never a miss for is extremely high quality. PLA:Bambu Lab - PETG: Blue GrayBambu Lab - PETG: WhitePrintingThe files were prepared and sliced with care, with...

Enjoy Parts and quantity to print: - 64x track_link-v7 - 128x track_plate-v2 - 1x Jig_for_assembly_v4 - 4x drive_cog-15t - 2x side_full-slide-F-v2 - 2x side_full-slide-M-v2 - 4x supp bearing-v9 - 2x supp gb and bearing-v8 - 2x supp moteur n...

BEC set to 3.66V RMS --> VCC Hall sensor board pin 24 Jetson (physical pin == number printed on pcb) --> D0 Hall sensor board GND to GND This configuration is listed on Slack from @Doug and @Tawn (https://donkeycar.slack.com). Thanks to them! I use...

To save time and money, I need to print new blades regularly. === SIMILAR STAFF === My search on Thingiverse led me to this page: https://www.thingiverse.com/thing:3025985 As a difference from olavl's design, I sketched one blade and rotated it...

Document description: This design is divided into two parts: core and shell skin; The shell part is open source and can be modified at will to add personal identification; The core part can be modified and adjusted according to your own needs, but...

Threads for fastening the spindle nut with 4 M3x15mm cylinder head screws are also printed. 2020/03/09: Version 1.0.4a: Version without a cam for triggering optional limit switches. 2020/03/10: Smaller dimensional changes: Distance between spindle...

The maximum dimensions of a TFT screen that you can put inside this monitor are given at the end of this description.You need to download and print all the files from the standard version, except CRT and FRONT-GRAY-FRAME, they are replaced with the...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

Edit 08/01 - Hey everyone, just as a heads up, this was designed to be the same size as the 'traditional' walker named after a type of battleship but after printing it myself I realize its a little bit bigger then I thought it would be. For...

These prints require very little support if oriented properly with the rectangular sides face down - but you'll need good bed leveling and a smooth bed to get a good outside surface. There is support necessary around the SD card slot and HDMI ports....

... so I installed three spacers. His desk is now rock solid. It actually worked out pretty well.Print SettingsPrinter Brand:CrealityPrinter: Ender 5Rafts:NoSupports: NoResolution:.16mmInfill: 100%Filament: Overture PETG White   Category: Office

The print itself is only a case and a lid, but I thought it may inspire some other creative invention. I apologize for the poor quality of the video and my gross fingers. It was really hard to get the camera to recognize the led screen because of...

PLEASE CHECK YOUR PCB SIZE BEFORE PRINTING! I MEASURED MY PCB WITH A DIGITAL CALIPER AND IT MEASURED 65mm X 39mm EXACTLY Note there are many versions that look similar but have key differences. Make sure you use the one that is exactly as shown,...

Here's what you'll need: * 10 M3 nuts * Arduino Nano ($2.79) - https://www.aliexpress.com/item/Nano-CH340-ATmega328P-MicroUSB-Compatible-for-Arduino-Nano-V3/32572612009.html * Step Down power supply ($1.09) -...

If you want to use the RobotGeek Servos print the part with the "_RobotGeek" ending, otherwise use the "_995" Parts. We tried to use as many snap fits and screw connections as possible. Only the camera holder for the picam, the speakercap and the...

Materials needed: You will need to print the 6 gear bearing: https://www.thingiverse.com/thing:53451 ** Thanks emmett ** 12v motor 12v variable resistor with dial 10' long speaker wire 10' long lamp cord female power plug 3' copper pipe brass...

That being said, Creality did an exceptional job with the CR-10 that third-party manufacturers can duplicate it using the cheapest, lowest-quality materials available, and still manage to print beautifully with some elbow grease. I say my CTC A10S...

I use this: Amazon link Some cable connector like this: Amazon link If You enjoyed this project and You want to say "Thank You" please consider supporting me by sending a tip on thingiverse or my PayPal here. I hope you enjoy it! Print Settings...

you may want to do some dimensional tests first to ensure that there's not a significant difference between them--I did have some minor fitment issues that required slight sanding when I tried mixing several different PLA/PETG/SLA resin prints. My...

The printed version doesn't grip the shaft on which the thumbstick was mounted as well as the original part and may slide a little over time. If you follow this design exactly then you have 2-3mm to spare. ## Installation instruction (crude) ...

... Done with Base Save as Part (*.prt) And as STL If you want to print later. The top screw Again start with a hexagon 2.5 wide 0.5 tall. Extruded base, make a circle in the middle 1.5 wide 1.7 long (This way you can be sure it screws in all the way).

Last but not least, tighten the fitting tightly (this will press the inliner firmly against the nozzle.Without filament, heat up the hotend, put on the nozzle, let it cool down and print until the doctor comes. ...Of course, don't forget the bowden from...

(ALL OF THE ABOVE ICONS ARE ALSO SOLD SEPARATELY ON MY PROFILE.) (MIRROR THE ICONS FOR USE ON THE RIGHT SHOULDER PLATE SO THE ICON IS FACING FORWARDS AS INTENDED, THIS CAN BE DONE EASILY IN ALL SLICERS) These models are designed to be fitted atop...

Now you can print your own frames using the same shape files used by Flite Test to cut the delrin and carbon frames.\r\n\r\nWe'll be releasing more frame designs in the future as well as free plans to go along with them. And in the swappable spirit,...