3d printed mining rig

When printing this jig, the only supports needed are below the two alignment fingers. When you import this part into your slicer software, it will likely need to be rotated to lay flay on your build surface. 1/2" PVC - Metric Drill Bit [1/2"...

With the exception of part "Rear V3 P2.stl" all parts can be printed without support. Layer height 0.2mm, infill 35%. The holes for the LED may have to be redrilled to match the diameter of the used LEDs (indicator LEDs 3mm, all other 5mm). The...

The only parts from the cad file I plan on printing is the pass through 4 way connectors. They are measured out so that a 3/8th inch Schedule 40 PVC pipe can slide through them and connect on either side. Technically with these connectors you could...

Instructions: Print in following order to avoid delays: 1) Left wall assembly To begin installing your Spaghetti Dispensing device first secure a piece labeled 'Left Wall.' Identify round portion from corresponding hopper elements, which should...

It is slightly overwheeled, the S-class has smaller wheels than the Jinty, but it is close enough for a reasonable approximation, and if anybody fancies making a specific printed or brass chassis, or just rewheeling the Hornby donor, then please let...

Personally, I prefer the 2U design, but if you only need up to 6 units, you can save space and have an upgrade path: * https://www.thingiverse.com/thing:4125055 Here are all of the parts needed for a complete 12-Pi cluster: To print: * 12 frame...

Assembly I printed all parts with ASA, I glued the "5015Halter" to the component cooler with acetone. Fasten the "Grundplatte" with M3x10 screws. For the "Schlauchklemme" and the cold end fan, drill out the holes with 2.5 mm and screw in an M3...

This is a Custom-Made Starter Box for the 22RE Toyota Engine https://www.thingiverse.com/thing:644933 My completed project can be viewed at https://www.thingiverse.com/make:692499 # Print Settings 1 x StarterBody1 : Layer:0.15mm Raft:no Support:no...

Bollards (cross)- print several pieces and glue in vicinity of chocks. Ballast tanks can be filled through ballast vent pipes and emptied by syringe with flexible pipe connected to sounding pipes. Pay attention during ballast operations- excessive...

Thicker panels and prints good now in 1/25th scale *UPDATE: 10/09/21* Uploaded a revised truck bed, this time with wall supports, Rev B *UPDATE: 10/06/21* Revised the truck bed, made the walls a little thicker and smoother, Rev A for both Pro Street...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out. Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. …...

A modular board design helps with capturing the fine details of original design, as larger individual tiles can be separately printed even on smaller beds; additionally, the tiles can be easily stored. **Game Rules** Each player takes a set...

Mi sembra di avervi detto tutto.Buona stampa._____________ Kitchen Sink Carpet Hi, this is a simple but functional drainer for kitchen sink.Why did I do it?Being in quarantine for COVID 19 like everyone else, not being able to go out to buy it, I...

FederationDN-V2-ship-stls.zip – Print-ready combined ship STL files. This kit supports the following variant ship classes: Federation class dreadnought The original TOS-era three-nacelle dreadnought from Franz Joseph’s 1975 Starfleet Technical...

Print all parts as already oriented with no supports. You will need 2x 'Tronxy X5s belt aligner wheel'. You will need; 2x M3x6mm bolts (for bottom mounting) 2x M4x30 bolts (for belt aligner mounting) 2x M4 nuts (preferably nyloc) (for belt aligner...

Pack Contents - 56 Page Multipage .PDF Booklet suitable for Printing, if you so wish. - 4K Resolution Digital Maps, including; - 19 4K Resolution Once Bitten Ship Maps;Captains Cabin (Room), Forecastle, Captains Cabin Layer (Sea), Gundeck, Gundeck...

Needs plenty of support when printing it. Please use the shortest machine screws you can for each of the fittings. You need to heat press the nuts all the way into the recesses. Use countersunk head machine screws for the hotend clamp as the top...

Another entry in the line of action figures I'm 3-D printing because the real ones way too expensive for me to afford to buy! Sources arms and legs modified from Baby Animal by R1N6MAN https://www.thingiverse.com/thing:4642359 head from Jim...

You can also refer to this video from Embrace Making for dissasembly assistance, it helped me so much when I was trying to do this I've tested it on all-metal version with dual-fan setup, you can refer to my klipper config if you need to (Please...

Plus tiny stool.  - Cupboard with microscope top option All the parts are pre-supported for SLA resin printing! This set works together with the Medical Bay set (the table, drawer & cupboard top options are interchangeable - there is also some...

Requires 18mm or ¾" holes in the lid and tub for mounting - use a spade bit for a cleaner cut as these containers are quite brittle.A full unit requires 1x Post (Lower), 1x Post (Upper), 2x Sleeves, 2x Through bolts, 2x Bearing Cups, 3x Arm (Hole),...

This brings me to this new part – it's essentially a clone of a design by Mangtronix http://www.thingiverse.com/thing:280974, but after printing his part I realized it wasn't long enough for the Wanhao Duplicator i3 (I didn't realize at the time...

Then, generate the .stl files.\r\n\r\nPainting Instructions\r\n======\r\nThe marble paint scheme was based on Raffa's marble painting tutorial available online.\r\n\r\nThe tiles were printed using natural PLA and then welded to their bases using...

I changed it because I didn't like the doors beeing in my way when using my printer from one side of my table.You don't need any clue the doors are held with small printed screws. I only have the screws at the bottom and it holds the whole door when...

Gcode Start Gcode * G21 (set to metric) * G90 (change to absolute positioning) * G28 (home all axes) * G1 Z100 F3000 (move to start height) * G1 X20 Y10 F1500 (move to start position) End Gcode * M106 S0 (turn off cooling laser) * G90 (change to...

I printed these parts using a delta-style printer, employing the following settings: For the Rings & Handle: - Layer height: 0.2mm - Outside perimeters: 2 - Top and bottom solid layers: 3 - Infill density: 20% full Honeycomb For the Clamps: - Layer...

Mount the printed spacers on the Raspberry board, by sliding them around the tubes. 6. Mount the 3.5” TFT screen on the Raspberry Pi board using the GPIO connector. 7. Mount the whole assembly on the right side of the main panel using four M3x10...

To assemble the kit, you'll need to print: 1. Base Z 2. Base XZ 3. Base Y 4. Base bed 5. Fan start link (for X) 6. Y end link 7. High B 40° link 8. 37 high B links 9. 23 low B links 10. 11 low 5° links For the Y, start with the Y end link on the...

With these, it is now possible to make a working boomerang that can be manipulated after the fact by dragging around the control points of the Bezier curves.The airfoil is kind of crude, since geometry nodes don't seem to be able to do bevels right...

The STLSs are up, I have validated Most of the Prints, but not the barge as of yet. I have done heavy design work on these models, however I consider them remix's due to the heavy amount of various Thingiverse parts, so credit where it is due. The...