3d printed packout mods

Corner organizer for the larger (non-wheeled) Milwaukee Packout toolbox to hold nine screwdrivers. Currently sized for four Greenlee screwdrivers and five Klein nut drivers. Can be printed in PLA/PETG, but TPU adds extra impact resistance. ...

This is a set of Mounts to hold the milwaukee knee pads on the back of a rolling packout box under the retractable handle. ...works pretty well

This is a flip over table for Milwaukee packout trolley.I needed a small table for the laptop and this works great for that.

a packout mount for Milwaukee level. no screw need. ... For normal level not Redstick ;) Remix of https://www.thingiverse.com/thing:4533364

Dividers for Milwaukee packout. One is a single piece for splitting the box in half. ...Other two are for splitting the box in four separate compartments.

Although I'm sure it will fit other cordless tools and sockets, I am using: - Ridgid R86011 - Ridgid 2Ah Battery - Dewalt 23pc standard depth socket set (DWMT74739) - Tekton 1/2" Universal Joint (SAI22102) Note this design will house all of the...

... drilling into your vehicle. ... Hardware Needed: 4x - Packout Plate Car Foot.STL 8x - 1/4-20 Socket Head Cap Screws 8x - 1/4-20 Locking Nylon Nut 8x - 1/4" Washers (OPTIONAL) These will soon be avalable for purchase at: https://www.3dprintingmi.com/

ORIGINAL:Just started using the Milwaukee Packout system for camping gear and decided to make a simple attachment to hold a small fiskars splitting axe that leverages the bracket that keeps the drawers closed.Built in Fusion 360, ideal print is on...

Here's a DIY 3D-printed mod that can convert any OFO bike into an electric-assist system in just two to three minutes. You'll need to attach the DIY controller and the DIY friction-drive unit to the bike, and you're good to go. Below are the parts...

You may want to print the "pair" model as they have been resized to fit exactly around the telescoping posts. Depending on your printer's dimensional accuracy the fit might be a bit tight and you may need to file away at the corners or increase the...

Individuals can easily install dividers that perfectly fit into the compact 48-inch tool box from Milwaukee PackOut. ... These dividers require minimal setup and no additional support for a seamless installation process.

Currently sized for four Greenlee screwdrivers and five Klein nut drivers. Can be printed in PLA/PETG, but TPU adds extra impact resistance. Fusion 360 file included to customize to your toolset. Current hole sizes are as follows: 7.8mm (Big +)...

Many thanks to codyrubin123 Packout Fish Stick Bracket from April 26, 2020. I use their design for the bracket and just add the holder for the pole. I use the same 8-32 hardware for this build. There are 2 pieces a bottom and a top with a hole all...

This is a divider for the Milwaukee 3 drawer packout box. It is sized to fit on an Ender 3 bed and will require two pieces to make one full length divider. ... There are no connecting features, but I found that applying tape after inserting into the...

i have created printable labels for all my packout. ...i only have a single filament printer so i recessed my letters and used 5 min epoxy and white pigment to fill them in flush, but left the files blank so you can change them to your needs

I made these so I can attach my set of Klein Tools Flex Rods (https://www.homedepot.com/p/Klein-Tools-15-ft-Mid-Flex-Glow-Rod-Set-56415/204178243) to my packout kit.The hole has a 30mm diameter, so you can also use this for carrying a small pipe or...

As soon as I discovered the logo plate was removable from the new drawers I bought for my packout, I knew I needed to replace it with something. A couple hours later, I had everything I needed. The latches will probably break when being removed...

Fish stick holder for the Milwaukee Packout. Holding my Klein fish sticks is a breeze, as the tool squeezes the Klein tube snugly, and I'm confident it will fit other brands too - you can simply measure your tube to ensure a perfect fit. ...For this...

It helps prevent the annoying problem of your drawer dividers lifting up and out of the molded channel in the front of your packout drawers. Print instructions: Recommend printing horizontally as oriented, using supports to keep the little...

This is a simple friction fit Apple AirTag holder to slide in to the lid of a Milwaukee Packout Rolling Toolbox. The design is very simple and the 4 voids were inserted to reduce filament usage. I recommend using black filament so that the piece...

This is a latch I designed for Milwaukee Packout Add-ons, which I used to create a small bench top. You'll need 3/4 inches of space - I utilized the remnants of my 3/4-inch plywood benchtop for this project. If you appreciate what I made, please...

I was looking for an easy-to-print and easy-to-assemble face shield. Many thanks to HanochH for his great design. I added some breathing holes and stabilizers. Now you can assemble a ribbon without a knot. I used 200 micron (0.2mm) PVC...

Hope this helps someone out! This Hacksaw- https://www.homedepot.com/p/Milwaukee-M12-12V-Lithium-Ion-Cordless-Combo-Kit-5-Tool-with-Two-1-5-Ah-Batteries-Charger-and-Tool-Bag-2498-25H/310549979This Milwaukee Packout-...

I have added 4 comer supports and they will go on base of the Packout to support each corner of the tray. You went them to poke though the foam and the foam helps them stay down with a bit of super glue.. ... I got a sheet of Aluminium Composite...

These models fit both the wide milwaukee shockwave bit box's and 3d printed Packout bins. ... These will hold 1/4" sockets and I have included both single and dual socket holder models.

With 3 screw holes. ...When printing you should flip it upside down.

Holds a set of wrenches in various sizes from 1/4 to 9/16, plus wire stripper and sidecutters. ... I printed in TPU to avoid shattering

... them did not arrive with the internal bins. do I have decided to create my own. I assume they will also fit Milwaukee 48-22-8430 as they are the same Hight. In the photos you can see a comparison between the original and the printed ones. ...

If you want to use the fusion360 file to make a better version you can send me an email: Emileleenen@outlook.com I recommend to print the top and bottom with 2 layers, otherwise this takes a lot of filement and time. @goedgereedschap is my...

This is a self-built 3D printer built using 3D printing technology. ...The owner provides all necessary parts, including nuts, bolts, and slide rails, to assemble the machine.