3d printed snowflake

The one on the left in the picture above is not necessary, if you have already printed the original version is will still work fine. But the one on the right needed to be changed to clear to USB jumper/adapter/180 degree thing.  I chose to use the...

... the key « f » for fillets.</p><ul><li>Draw a sketch an the top circle under the helix with a little rectangle who will « join » the eagle wings. By doing that, you will have a better print by having less retraction.&nbsp;&nbsp;Category: Automotive

Take care to ensure the Adapter port with the wires has been sanded to remove sharp edges & serrations from the printing process. Slide the Adapter over the motor and secure with a 2.5 to 3.6mm wide zip tie. A pair of pliers will help to pull the zip...

Print them as I have shown in Cura, with or without supports. The vertical holes will be fine; it's the very hole on the bottom that gets stringy, but it still works. I was going to add a small cylinder in Fusion and make a pre-modeled support but...

I would love to see what it is being used for! If you like this thing, have as aswell a look at: https://www.thingiverse.com/thing:3239814 everything that this thing can do can be done as well with the newer thing. But it has a lot more options and...

You'll need to print two of these, but don't worry about mirroring since this is symmetrical and so is the gap it fits into. You will need to upscale this object by 12.7 times or with an X, Y, Z of 101.6mm x 31.74mm x 10.38mm. With this scaling,...

* As an alternative, you can print the nosecone I've now included with this thing. 20% infill should be fine and it will weight the nose without gluing on nuts. There is a recess in the nosecone for the knot from the shock cord to fit. This nose cone...

This is printed and tested and works, though I prefer the regular rollers in this design. (UPDATE - posted here: https://www.thingiverse.com/thing:4979880) * I also designed a mount for a 2020 rail, such as the top cross rail on an Ender3,...

That said; I'm still using it, and in the context of how I want to use it, it's much better than the tray I had designed, and better than the other thingiverse smoother cases I have seen/printed. So consider it as a silly idea that's going to work...

... drill holes for the magnets in the block. The Display Base was too big to print as a single part on my printer, so I split it into 'a' and 'b' parts. ...The two halves of the Display Base can be connected using two M3x12 screws, washers, and nuts.

This set includes all the printed parts which go along the metal plate (source form e.g. <a...

Before starting, assemble the cylinder by sealing it (there are holes on the sides) and printing it from transparent material for better visibility. If you give up, you can disassemble the game and try again. Good luck! HINTS: This game aims to...

**Instructions** - Print one copy of the Piédestal and of the Cercle cranté (that's pedestal and notched circle for you english speaking people) and six copies of the Secteurs (sectors). I advise to join the sectors by twos (a simple adhesive is...

Do not glue the skewers into the holes; even if the printed part literally just falls off the skewer, winding the thread onto it will keep it all securely together. ...Not gluing the skewers in will also let you remove the skein label and reuse the...

I tried to keep the list of printed parts minimal by creating a two-gear system instead of a more complex scissor extension arm. A unique feature of my design is the guide wheel that supports the tracing gear to keep it level and from falling into...

The ball housing needs to be printed in black for it to trigger the sensor properly. The ball is a tight fit, and I use PETG filament; I press the ball in with pliers. When the filament is absent, there's a 8x3mm round magnet on the back that pulls...

If you're not using a hole that has been cut, then there is a cover so your nutrients don't get light.Use a 51mm hole saw and you have a water filling hole and a hole for the water level gauge.General printingEverything is aligned for printing...

It is highly recommended to print this box in PETG due to PLA's tendency to deform over time under compression, compromising the box's structural integrity. To further enhance stability, consider supporting it from below with rubber feet, ensuring a...

Besides printed parts, you'll need to complete these hardware requirements: Lid: (Button Head Screws ONLY) Six M3 6mm or 8mm Button Head Screws Eight M4 8mm Button Head Screws Inside Box: All Boards: M3 4mm Button or Cap Head Screws Fans:...

... Done with Base Save as Part (*.prt) And as STL If you want to print later. The top screw Again start with a hexagon 2.5 wide 0.5 tall. Extruded base, make a circle in the middle 1.5 wide 1.7 long (This way you can be sure it screws in all the way).

For VTX antenna, I use TrueRC Singularity short ufl LHCP antenna https://www.racedayquads.com/products/truerc-singularity-5-8ghz-short-u-fl-antenna-rhcp-or-lhcp?variant=31387077476465 Print using 0.2mm layer height. 100% infill with support. For...

Vous aurez besoin pour la partie rotative de : 6 roulements de roller Øext 20mm Øint 8mm épaisseur 7mm 4 écrous marteaux pour profilé T20 4 vis pour les écrous marteau l'extrudeur MK8 en plastique la visserie d'origine de l'extrudeur mk8 en...

I had to print that after a craftsman tried to shorten the doors length in a rather barbarian style. The door is 83 cm in width - armed with an Ender 3 this translates to 4 parts with 205mm length each, leaving 1 cm uncovered as the door is so...

Printed all the parts with PCTG. Geänderte und verwendete Dinge aus: Changed and used things from: Adjustable LED Strip Backets https://www.thingiverse.com/thing:2207879 40mm Fan turbine cover with Dust Filter ...

Print the holder, of course 2. Upload the two G-code files and run them without the holder and gauge, just to be safe 3. If everything works out, fix the holder with the existing fan screws 4. Install the NEOTECK gauge and... 5. optionally, use a...

Scan the sheet using a geometrically accurate scanner (for example the ScannerPro app on iPhone making sure geometry correction is enabled.). Follow this youtube guide to import the scanned image into FreeCAD and trace the contour of the lens. Pad...

* If the battery compartment clip prints too weak or breaks off, you can wrap electrical tape around the controller just beneath the grip button to hold the cover in place. <h1>Miscellaneous Q&A</h1> * <b>What is the battery life?</b> I measured...

Print Settings Nozzle size: 0.40mm Layer height: 0.16mm Infill density: 100% Nozzle temperature: 230°C +-5°C Bed temperature: 60°C Cooling: 50% Support Overhang Angle: 85 Build Plate Adhesion Type: Brim Disclaimer: As you all know, producing the...

... The clips should move smoothly otherwise they will not grip the eyepiece very well. These were printed with support, but designed to work without it. If you encounter any issues, please let me know. ... Arsenal's website is arsenaLproducts.com

For the same price of one tent pole could buy 2 x 6.5m lengths of Al tube, and a roll of filament.&nbsp;Took a few attempts but the twist lock cams were very easy to design and print and worked far better than expected. &nbsp;The larger version...