3d printed spool

An universal, fully 3D printed rolling spool holder. No screws, bearings etc. required. The 3D printed bearings work quite well (better than the ones i tested here from thingiverse) and can also be used for other projects. ... CAD file available.

An universal, fully 3D printed rolling spool holder. No screws, bearings etc. required. The 3D printed bearings work quite well (better than the ones i tested from thingiverse) and can also be used for other projects. Fusion360 project file avilable...

3D model for 3d printed spools. ...You can print with whatever colour and infill you want.

follow the instructions here: http://www.instructables.com/id/3D-printed-Spool-Holder-Smooth-as-butter/

This spool holder can hold any sized roll less than 10.5 CM tall. ...This is made from all 3d printed parts.

... for the excellent Bukobot printer since it doesn't ship with a spool solution. (Check back; I'll be adding different width bottoms as I come across different size spools.) Instructions I printed in PLA using .15mm layers and a 40% rectilinear fill.

3D Printed Filament Spool for filament samples. ...Optimised for the best printing quality on FDM Printers, Support Free and doesn't need glue to be assembled.

3D Printed Filament Spool for filament samples. ...Optimised for the best printing quality on FDM Printers, Support Free and doesn't need glue to be assembled.

3d printed filament spool to mount your filament that comes in a bag. The two sides are identical, just print twice, and then print the hub twice by modifying the spoolhubortest variable to 1 in "3d printable filament spool configuration.scad"You...

This is a 3D printed spool stand for the printrbot. It is used to hold the plastic spool in the side of the printer to provide a smooth unrolling action. You need 4 roller bearings and 2 bolts and nuts (optional). ...

i design it to use the minimum amount of filament and not required support. ...it has filament holder in the end and start of the spool, you can also use zip tie. ... The two parts screw together, no need for glue or screws.

Incredibly over-the-top filament holder, utilizing the prolific 3D-printed bearings found on here. Everything is 3D printed. The axle shaft expands and contracts ~15mm in diameter; I haven't found a spool of 1kg filament that the mechanism cannot...

Everything is 3D printed.The axle shaft expands and contracts ~15mm in diameter; I haven't found a spool of 1kg filament that the mechanism cannot accommodate. Can add larger leaves if needed for some large ID spools.You need a rubber band to go...

I designed it a bit tighter so the filament doesn't unwind itself.Needed Parts:- 6x M4 20mm - Socket Head ScrewsPrint Settings:- i printed mine with 0.2 height and 0.4 width / 4 Parimeters and 5,5% Gyroid Infill, but i should work with another...

Assembly Steps Step 1: 3D print the following parts: 4 x bearings --> this should be a good quality print with at least 50% infill. 2 x body 2 x shaft --> You might want to scale this along the long axis if you find the holder too big. The length of...

I printed a spool holder for 3D printing filament spool.Dimensions of the spool, Diameter: 200mm (7.87 in), With: 55mm (2.16 in).Although my spool was 53.5mm wide.You will need: 4 608 bearings.

My entry for the 3DPN 3D Printing Design Contest. ...   Spool holder for Joel Telling's, aka the 3D Printing Nerd, spool shelving. ...Includes embosed "3D Printing Nerd" and "#HighFive"  text.

This is a 3D printing filament spool holder for any type of spool. This spool holder has two arms that reach out to hold the crossbar that u hang your spool from. ...The arms also have an extention block so that you can fit your larger spools on This is...

A Spool holder for Joel's 3D Printing Nerd Spool Holder Competition. The half with the smaller  non-counterbored holes needs all 4 tapping with an M4 tap - these can then be screwed together with 2x 20mm M4 screws and 2x 8mm M4 screws. ...  

3D Printing Filament Spool HolderIt's designed to be used with a pair of bearings with the specifications below:6 mm inner diameter 13 mm outer diameter5 mm width6 mm shaft collars and 6 mm rods can be bought on Ebay or Mcmaster-Carr.There are two...

3D PRINTING FILAMENT SPOOL HOLDER It's designed to be used with a pair of bearings with the specifications below: 6 mm inner diameter 13 mm outer diameter 5 mm width 6 mm shaft collars and 6 mm rods can be bought on Ebay or Mcmaster-Carr. There are...

A small project to allow me to use my drill to spin filament from full size 1kg filament spool to 0.5 kg filament spool for a Flashforge Adventure 3 Lite. ...

2018/08/02 - Added 3 bolt thread sizes: 45, 65 and 85mm Obs.: This is the bolt thread length, to find bolt total length add 28mm (cone length) Print Settings Printer: iTopie Supports: Doesn't Matter Resolution: 0.4mm Infill: 20% Notes: Nozzle 0.4mm...

This is an exclusive design for printing spool. It has several amazing designs, such as and X design spool base to enhance the durability and stability of the filament, also to lock it with four squre at the end. Another is an locking design that...

This is an exclusive design for printing spool. It has several amazing designs, such as and X design spool base to enhance the durability and stability of the filament, also to lock it with four squre at the end. Another is an locking design that...

This is a 3D printing empty spool made to convert the 3D pen filament roll into filament used with a 3D Printer. For assembly it needs a M3x8 countersink screw. ... 1 x M3x8

3D Printing Nerd Spool Holder Design Challenge.Requires printing of the file twice to have required components for holding spools. ...File contains all parts for 1 complete bracket assembly.Brackets rest on top of front rail and bottom of back rail,...

It's available for download from the 3D Printing Association and Youmagine.Originally discussed here - http://richrap.blogspot.co.uk/2014/03/universal-3d-printing-filament-spool.htmlOverview video here - comment, feedback and if you decide to adopt...

This is my design for Joel Tellings (3D Printing Nerd) spool holder competition. Each half makes one holder and needs a total of four printed piece to work as planned. This design also requires some bought hardware as listed below: 8x M3 3mm Screw...

I have designed this spool holder for the 3d printing nerd on youtube for his spool holder challenge