pocket door floor guide 3d models
175137 3d models found related to pocket door floor guide.thingiverse
Replacement bottom guide for pocket doors / sliding doors. ...Printed on ultimaker 3 using nylon with 100% infill.
thingiverse
Pocket Door Guide Replacements to help keep the door on track when sliding open and close. Original is in white. ...Replacement parts are in black.
prusaprinters
I created this model to keep a pocket door from getting stuck and misaligned. I designed to have a base that fits under the door and attaches to the floor with pocketed screw holes. I positioned it so that whether the door is fully open or...
thingiverse
... a loud scraping noise while the door slid open and closed. I printed it out of clear PETG to make it as invisible as possible without taking out the door. Fusion 360 File is included in case the space between the floor and door is different. ...
thingiverse
A pocket door in my house was missing guides and so was scraping the inside of the wall. ...The basic shape is pretty tough, installs with 1/2" wood screws.
pinshape
To guide a pocket door with no bottom grove in the door. Sorry photos are of an earlier design I have not printed this design yet. The new design has screw hole guides and bevel edges to reduce the chance of damage to the door. The "U" part is...
thingiverse
I installed some new sliding pocket doors in the house and I did not like the little plastic guide block hardware it came with....these guide blocks fit at the bottom and make sure the door does not swing and hit the walls. The last picture above...
thingiverse
Repair part for a pocket door. The adjustable slider, which prevents the door from just banging about is often broken. ... Here is a quick design to replace one when broken.
thingiverse
Floor guide for a thick sliding door with a slot in the bottom of the door
thingiverse
Floor guide for sliding doors, typically need two guides per door. ...Dimensions: 26mm (h), 45mm (w), 20mm (l)
prusaprinters
Floor guide for sliding doors, typically need two guides per door.Updated 2022-02-05Redesigned as two parts to increase strength. Mine snapped off when knocked along a layer line. The new design is a push fit of the guide into the base from the...
prusaprinters
This is a bottom door guide for keeping the barn door from swinging away from the wall. To add strength, a 5/16" carriage bolt is fastened through the center and clamped lightly with a 1/4" washer and 5/16" nut from below. ...The door guide is screwed...
thingiverse
exact copy of barn door guide ,i made it on freecad. ...used petg for strength and can flip print so layers work in your favor
prusaprinters
My doors didn't slide back as well as I'd liked, so I added a little guide for the doors. ...Once everything is put together I used double sticky tape to find the best position for the guides and then screwed them in with wood screws.
thingiverse
My closet door fell off its tracks as the existing floor track guide was broken. I drew this one up as a replacement. The screw holes to affix it to the floor are 4 inches apart. It should accept doors as wide as 1.4 inches. Print the bracket on...
thingiverse
This is a sliding closet door floor guide designed for a two door sliding system. The base is 4mm thick and the vertical columns are 27mm tall. The holes are 107mm apart from center to center. The two gaps are 36.5mm wide. ...This was made after the...
thingiverse
this guides 2 doors to slide in front / behind each other to access one side of a closet or another. This is not for "bi-fold" doors... it is for closets with 2 large doors which overlap in the center and can slide left and right in front / behind...
thingiverse
This is a taller version of another sliding door guide. Original --> http://www.thingiverse.com/thing:70747 I made this to go with doors that are hung slightly higher off the ground. ...This works with sliding doors 5mm apart or further, with a max...
prusaprinters
Bernard, the thin hardware store closet door guides don't stand a chance. ...I modeled this to be a drop-in replacement – and tougher.Print it with several perimeters for strength.Slice it with the screw plate vertical (and on top) – this will give it...
prusaprinters
My sliding door guide broke so I made a replacement for it. I printed it in PETG to make it strong. ...I recommend printing it on its side as my first print eventually broke along the layer line when I printed it with the bottom to the build...
thingiverse
A simple floor mounted "hidden" barn door guide. ...Its a rough copy of this part: https://is.gd/xcGRHp - ~45mm x 24mm x 4mm - Main guide is 20mm tall from the floor - Secures with two screws 4 perimeters and 25% infill
thingiverse
Using a level, make the guided door level and adjust the tracks on the floor as required to maintain door level through entire length of travel a. Mark required screw location for floor track with pencil or masking tape if possible 7. Remove the door...
thingiverse
Guide for sliding doors designed to be attached to baseboard with screws. The first model has an overhang designed to accommodate the way my particular baseboard/door jam fit together. Also includes a L/H overhang for the other side of the door jam,...
thingiverse
The guides included with my pocket door didn't extend quite far enough to guide the door back into the pocket when it was completely closed. I made a version that was .444 wide at the base initially and tapered to the top, but it was a bit too thick...
thingiverse
This is a small guide for drawing ellipses that fits in your pocket. ... If you like small art tools check out my pocket-art-kit video: https://youtu.be/oEu40uVIuHg