3d printer extension
1857152 3d models found related to 3d printer extension.cults3d
External house / holder for 3d Printer MicroSD to SD card adapter. The holder's inner hole: 36x12mm. You can use this holder on table in front of the printer or attached to the side of the printer. This holder hides the long ribbon cable on the table...
thingiverse
... end. I realised i uploaded the wrong nut, so i have replaced it with the correct one now, sorry for anyone downloading the previous nut. it was too tight. Print Settings Printer: Wanhao Duplicator 4 Rafts: No Supports: No Resolution: 0.2 Infill: 10%
thingiverse
These two files are for an extended Y-axis version of the Daemon 3D printer, increasing the Y travel by 50mm. That's the maximum I managed to get without significantly affecting the quality. You will need a printer with a minimum print surface of...
cults3d
--The model is compatible with ANY profile maded printer (Creality printers, Tevo's, BLV cube and more!)-- Wanted to stylize a CR10 that I've fixed. The idea is to make small legs with rubber pads that would look like 2040 V-slot profiles. It will...
prusaprinters
:-) Bed heats up to 100 C in approx 5 minutes now, is very stable and even 120 C is no problem! Note that my heat bed is not a regulat 12V heat bed, it can be configured for 24V when connected differently, so that's what i have done ;-) Category: 3D...
thingiverse
I made a box to mount on a separate 24V power supply Until now, my 3d printer has been given 12V to the heat bed, so it takes approx. 20 minutes to heat it up to 100 C (while covering it with some insulation on top). After that it struggled keeping...
thingiverse
SD card extension holder for 3D printer I bought the extension cable at eBay.com.
thingiverse
... QIDI Tech printers which comes with a chrome spool holders that will only work with QIDI filaments. ...The spool extender will allows other brands to fit such as Hatchbox. Print Settings Printer: QIDI Rafts: Doesn't Matter Supports: No Infill: 100%
thingiverse
To create the box, you will need to print 8 corners 90° 3 branches. for a box of U30 Pro for example, I chose 4 aluminium tubes 20x20x1.5 of 2m that I cut to give a cutting plan of : 4 tubes 20x20x1.5 => 1m 8 tubes 20x20x1.5 => 50 cm If you...
thingiverse
Extension for the exhaust port in the Glowforge Laser Printer
thingiverse
Hello buddies, A friend ask me to make a new paper exit extension for his printer. ...He tell me 3D print works very well :) Hope it help another one...
thingiverse
On my snapmaker I had a fault that I diagnosed to be a faulty heater. ...On fitting a replacement I decided to make an extension to the print head module so the cable would not be so tightly curved.
cults3d
Easy to make longer by printing more brackets or add to small folding table to extend the printer even longer. ... 608 bearings used Petg recommended it does not split as easy when inserting the pipe and the bearings The other version of the...
thingiverse
Easy to make longer by printing more brackets or add to small folding table to extend the printer even longer. ... 608 bearings used Petg recommended it does not split as easy when inserting the pipe and the bearings The other version of the...
thingiverse
... thought that it might be useful. ...I have a Qidi Tech 1 and X-Pro, I just tested it on the Tech 1. It fits a 1kg printer spool perfectly, with some slack, so should work with other 1kg Spools. ...You will just need an M10 x 50 bolt, nice and simple.
cults3d
... thought that it might be useful. ...I have a Qidi Tech 1 and X-Pro, I just tested it on the Tech 1. It fits a 1kg printer spool perfectly, with some slack, so should work with other 1kg Spools. ...You will just need an M10 x 50 bolt, nice and simple.
thingiverse
Print Settings Printer: HICTOP 3DP-17 Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Notes: Keep in mind that your print layer height, as well as any differences in height for the first print layer, will have an effect on how accurate the...