3d printer part cooling duct

... 5015 fan. ... I achieved the best possible results in my 3D Printer Test by combining this duct with a 5015 fan. ... To install a 5015 fan: * 2 M3/25 screws * 2 M3/6 screws * 1 M3 nut To install a 4020 fan: * 1 M3/18 screw * 3 M3/6 screws * 1 M3 nut

Replacement part cooling fan duct for Geeetech A10-20-30 M/T version 4 printers. The duct directs air from the part cooling blower in a circular patten around the nozzle. This provides better part cooling over the stock duct, that only blows from one...

... cooling duct that is standard on the Mk3S+. ...Orange fan duct was printed with the New fan duct which provides much better part cooling without causing the Hotend temperature to drop. This is a direct replacement. ...No modification needed.

Part cooling duct upgrade for CR-200B. Directs airflow more at nozzle. Uses all stock screws to mount. I am using a Microswiss all metal cr10 hot end mounted as stock hot end is same length within a few mm so duct should work with stock hot end...

Printer owners seeking to maximize their TronXY P802MA's performance capabilities are now able to take advantage of a newly developed part cooling fan duct upgrade. This enhanced duct system is specifically designed to significantly reduce warping...

The tool heads for this prototype have a ducted part cooling fan, and are designed for fans with very thin mounting ears, approx. 1.3mm thick. E3D had to get a new supplier for the fans due to the fact that the original supplier had fans which were...

This is a specially designed dual-part mounting system for a 50x15 radial fan, engineered to significantly enhance part cooling efficiency on the Anycubic Kossel 3D printer.

This is a part cooling fan duct designed to optimize airflow on the Creality Ender 3 printer. I manufactured this using Fillamentum ASA Extrafill, which offers superior heat resistance compared to PLA. ... 1.20.2018 - Version 2.0 uploaded for enhanced...

... Single side part cooling using a 4010 blower. Left and right fixing options. Blower clips in so only 2 bolt are required to attach it to the Hemera's stepper motor. I have it on 3 printers and so far it is providing adequate cooling for my needs.

I remixed biketigers ender 3 part cooling duct so it fits a 5015 blower fan. ...easy to print oriented backwards with supports touching buildplate

Part Cooling Duct for Flash Forge Inventor Works great as a direct replacement. ... Print in PETG, ABS, or other heat resistant filaments.

EasyThreed X1 and X2 part cooling fan duct for use with a 25x25x7mm, 12V, 0.05 amp fan, utilizing its original connection method.

This remix elevates AdrianSm's cooling duct to new heights, redefining elegance in 3D printing design. I've optimized the design to seamlessly integrate with E3D Volcano (clone), leveraging the same M4 nut and M12 screw as the original. A lower...

Ok, here's another part cooling duct for the Hermera exstruder/hotend assembly. Mine only blows from one direction across the nozzle. Permanoob beat me to the punch on posting this, and his design is great too! I used 40 degrees as my fan mount angle...

The E3D Tool Changer Printer is a Core XY prototype printer with many new innovations. It holds up to four separate tools for FDM printing, or whatever you wish to connect to the motion platform within the dimensional confines of the automatically...

This Rev2 version has a beefier fan mounting arm designed to prevent it from snapping off like the original.\nThis high-efficiency fan duct upgrade is specifically made for the stock part cooling fan on a Rigidbot 2 printer, and attaches using all...

(Same steps as the original so using some of the same pictures) The fan duct design directs a concentrated high flow moderate pressure stream of cool air across the tip of the nozzle parallel to the top surface of the part removing the heat quickly...

I designed a "fang" style part cooling duct for a 5015 fan, prioritizing minimal weight. The nozzle angle was updated to 60 degrees from vertical on October 27th, increasing adjustability in the duct's height and ensuring optimal airflow below the...

I designed a custom cooling blower duct specifically for my Maker Select Plus 3D printer. It cleverly utilizes the existing two bolts that secure the rear electronics cover, replacing the original cover with an upgraded blower type fan. This...

Unión de dos grandes diseños "Sidewinder X1 Part Cooling Fan Duct" y el "BlTouch de waggster mod". ... La distancia de offset es la misma que en el waggster mod: ``` #define NOZZLE_TO_PROBE_OFFSET { 31, -31, 0 } ```

The Tevo Little Monster comes with a pair of awesome 4010 fans for part cooling, but most of that cooling is wasted by only blowing air in the general area of the part.These fan ducts require no modifications to the sheet metal bracket, simply print...

This is a new version for the MK8 extruder of my DIY 3D printer. This time for a 40 mm part cooling fan. ... The location at the side of the steeper motor, is to avoid the right Z aluminum profile.

This is a new version for the MK8 extruder of my DIY 3D printer. This time for a 40 mm part cooling fan. ... The location at the side of the steeper motor, is to avoid the right Z aluminum profile.

... in PLA too. I adjusted the design so it would need minimal supports. How I Designed This Thanks to CharlieBeSuper for including the NF Sunrise STEP files in his fan duct design https://www.thingiverse.com/thing:5170732 Category: 3D Printer Parts

Human: Part Cooling Fan Duct for Tronxy XY-2 Pro This fan duct cools prints efficiently from both sides, preventing stringing issues that often occur on the left side of prints. I modified the original design by thinning out the brace wall, allowing...

... adapt HangTight's Hemera cooling duct to the BIQU H2. ...I've used several of James' designs in the past for part cooling and they are the best out there. All the better to have one on my new H2. ... Printed in ABS with supports touching buildplate.

It cools the part from two sides and directs the air right at the tip of the hot end. The stock cooler duct blows from only one side and nowhere near the tip. Print quality has improved and it prints overhangs better. ... I was going to go with a bigger...

Dual 5015 blower fan part cooling duct based on Hangtight (https://www.thingiverse.com/thing:4042492) ducts. Dont actually know if the placement is as optimal as the original. I highly suggest using threadlocker. I suggest printing the base in PLA...

Here's another part cooling duct for the Hermera exstruder/hotend assembly. Mine only blows from one direction across the nozzle. Permanoob beat me to the punch on posting this, and his design is great too! I used 22.5 degrees as my fan mount angle...

To ensure efficient cooling, the fan is securely attached to the hotend carriage next to the existing hotend cooling fan using a sturdy fastener. The duct itself fits snugly onto the shoulders to prevent any accidental over-insertion. This upgraded...